The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Harley Nolden Memorial Institute for Firearms Research

Reply
 
Thread Tools
Old February 5, 2007, 03:35 PM   #1
VUPDblue
Senior Member
 
Join Date: December 18, 2005
Location: Central Indiana
Posts: 1,978
Help with H&R Model 923

So I have discovered about everything there is to know about the H&R model 923 Revolver. Mine was made in 1955 and it is a 9-shot .22 with a 4" barrel. I have one very big problem with mine: it has no cylinder. The rest of the gun was given to me by the mother of a friend of mine. She told me that she took it from a friend of hers one night about 30 years ago when he came home drunk and waiving it around. Two days later, he was killed in a bar fight. Anyway, she took the cylinder out (that's how you load/unload the thing) and stashed it away in a box until I helped her move a couple years ago. She gave me the pistol (less the cylinder) and said she might or might not be able to find the cylinder. Anyway, I have been looking high and low for a new cylinder and cylinder pin for my little pistol with no luck whatsoever. I was hoping that someone on this board might be able to help me find one. Thanks in advance.

Nick
__________________
Silencers have NEVER been illegal !
VUPDblue is offline  
Old February 10, 2007, 09:11 PM   #2
VUPDblue
Senior Member
 
Join Date: December 18, 2005
Location: Central Indiana
Posts: 1,978
Found one! Thanks
Now it is whole again! Took it to the range and it works like a champ. Shoots pretty straight for an old cheap gun...


Nick
__________________
Silencers have NEVER been illegal !
VUPDblue is offline  
Old March 23, 2011, 11:21 AM   #3
Johnny2step
Junior Member
 
Join Date: March 23, 2011
Posts: 1
H&R 923 cylender

I have an H&R 923 as well. It wasn't in the best firing condition. As any firearm enthusiast will tell you, you can't dry-fire a rim fire gun because it will put a divot behind the shell where the hammer smacks the rim of the cartridge. The firearm was given to me for free but the person who had it before must have dry-fired it a lot because it's misfiring a bit. I'd like to get a new cylinder for it, if you could tell me where you found them and how much they'll cost. Thanks
Johnny2step is offline  
Old March 23, 2011, 11:55 AM   #4
aarondhgraham
Senior Member
 
Join Date: December 1, 2009
Location: Stillwater, OKlahoma
Posts: 7,072
Hello Johnny2step,,,

You might as well try and find a firing pin for it as well,,,
Dry firing often dents the cylinder but often peens the end of the firing pin.

That effectively shortens it as well.

Good luck.

Aarond
__________________
Caje: The coward dies a thousand times, the brave only once.
Kirby: That's about all it takes, ain't it?
Combat: "A Silent Cry"
Aarond is good,,, Aarond is wise,,, Always trust Aarond! (most of the time)
aarondhgraham is offline  
Old March 23, 2011, 04:57 PM   #5
32 Magnum
Member In Memoriam
 
Join Date: January 17, 2009
Location: Eastern PA
Posts: 364
The Model 923 is the Chrome or Nickel plated analogue of the Model 922. The model originated in or around 1949 and ran 'til 1952. The 2nd Model was introduced in 1953 and ran 'til 1961. The 3rd Model was re-introduced in 1977, and ran 'til 1979. The letter prefix in the serial number of your 923 will tell the year of manufacture and the variation. You will need to determine the year in order to order/find the correct parts for your piece.
32 Magnum is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07958 seconds with 9 queries