The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 28, 2011, 07:20 PM   #1
beaver
Senior Member
 
Join Date: May 29, 2007
Posts: 115
Dillon Square Deal B

i have a dillon Square Deal B set up in 9mm and the primer feeder is jamming any one else have this issue and how did you fix it.
beaver is offline  
Old February 28, 2011, 07:34 PM   #2
throttleup
Member
 
Join Date: February 12, 2011
Posts: 30
Dillon Square Deal

Yes, I've had that problem once or twice. Take off the primer feed assembly. Unscrew the threaded collar on the top of the tube and pull out the inner primer tube. Pull off the old plastic tip and replace it with a new one. You should have one in your spare parts pack. That usually does the trick. If those little split fingers get a little out of line or bent in any way it will start hanging up and drive you crazy. Bill
throttleup is offline  
Old February 28, 2011, 07:44 PM   #3
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,034
I would also suggest you take the primer assembly apart and clean it ( with Q tips ) not any solvent ...about every 3,000 rds or so ....

I no longer have the SDB model / but they're solid machines ....and easy to clean up / work on ..... and give Dillon customer service a call. The primer systems on all reloaders - need some maintenance.... ( I take my primer feeds apart on my Dillon 650 every time I change calibers / or about every 3,000 - 4,000 rounds / or whenever I finish loading a case of bullets.) If I do it every time I finish a case of bullets / its an easy part of the routine...
BigJimP is offline  
Old February 28, 2011, 08:37 PM   #4
beaver
Senior Member
 
Join Date: May 29, 2007
Posts: 115
Thanks guys will try those suggestions
beaver is offline  
Old March 5, 2011, 06:14 PM   #5
beaver
Senior Member
 
Join Date: May 29, 2007
Posts: 115
tried to change the tube as suggested did not work went back to basics and just started using the hand primer
beaver is offline  
Old March 5, 2011, 08:07 PM   #6
Bill Daniel
Senior Member
 
Join Date: February 10, 2000
Location: Bowling Green, KY.
Posts: 375
Dillon

Beaver the Tech desk at Dillon is top notch. Give them a call. I have used them several times over the last 10 or so years with my SDB and have always found they could solve my problems.
Bill Daniel
__________________
Prosecute criminals to the fullest extent of the law and their weapons will become harmless.

"Let us speak courteously, deal fairly, and keep ourselves armed and ready." Theodore Roosevelt 1903
Bill Daniel is offline  
Old March 5, 2011, 09:53 PM   #7
totaldla
Senior Member
 
Join Date: August 10, 2009
Posts: 670
If you are reloading in your garage, you need to warm up the machine. There are a couple parts that need to be pliable for the priming system to work. Also, Wolf primers are the worst when the machine is cold because they have rough edges.
totaldla is online now  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:39 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07769 seconds with 9 queries