The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old February 7, 2011, 11:24 PM   #1
jcsturgeon
Senior Member
 
Join Date: March 21, 2009
Posts: 291
Rock Island Armory Project

Well, I've had a Rock Island Armory .45 for a while, and I finally decided to make a project out of it. The RIA A1 is a no frills, no nonsense gun made to GI specs, but I bought a set of punches and a couple manuals and went to town. This was my first attempt at any kind of gunsmithing like this, and I am impressed by how it turned out.

I installed a Shok-Buff kit (new recoil spring and a full length guide rod), a aluminum trigger, a new combat hammer (with a new strut and strut pin) and I added some Pachmayr grips:





I'm not done yet, still looking for a beavertail safety, a stainless barrel and possibly an ambi safety and slide stop. I'm happy with it so far, and it shoots well. You can tell the difference in the recoil spring and it doesn't jam like it was prone to before. Any one else tackled a 1911 who has some feedback/pointers?
__________________
The Beatles were wrong, happiness is not a warm gun. It's a new gun.
jcsturgeon is offline  
Old February 8, 2011, 07:08 PM   #2
Libertad
Member
 
Join Date: December 30, 2010
Location: MI
Posts: 36
How much did that cost you? How much are you willing to spend on this project?
Looks pretty good, by the way. I like the colors on the grips with that slide/frame finish
Libertad is offline  
Old February 8, 2011, 08:05 PM   #3
k31
Senior Member
 
Join Date: October 26, 2010
Location: utah for the time being
Posts: 213
lookes good i have the mate nickle .45 and i will buy more from RIA in the future it is a gun that wants to be shot not displayed
yours looks good
__________________
"the best shooting firearm is the firearm you shoot best" Tony Marr
k31 is offline  
Old February 9, 2011, 08:07 AM   #4
jcsturgeon
Senior Member
 
Join Date: March 21, 2009
Posts: 291
Not looking to spend a ton, but I know it will add up. Just bought a new barrel that looks like it's parkerized... but stainless where it shows through the slide. That was $40. I guess if you add up all the parts I've added:

The Shok Buff Recoil System $38.95
Competition Match Trigger $18.84
1911 Value Line Hammer $30.43
Hexagonal Head Screws $9.97
Pachmayr Colt 1911 Grips Wooden Panels American Legend Series $26.97
Ed Brown Hammer Strut $7.39
Ed Brown Frame Rebuilt Kit $18.79 (Ironically I only needed the hammer strut pin, but now I have extras.

That's over $150 there (whew!) and I figure when it's all said and done I'll have put in about $200 in extra work, which isn't bad for a pistol I bought for $400. It's been a lot of fun and I learned a lot about the 1911.
__________________
The Beatles were wrong, happiness is not a warm gun. It's a new gun.
jcsturgeon is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:08 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07621 seconds with 9 queries