The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old February 7, 2011, 11:21 AM   #1
salvadore
Senior Member
 
Join Date: January 1, 2007
Location: Idaho
Posts: 1,793
conical

I just cast up a hundred lee conicals and lubed em up with lee alox. I was wondering if this is going to be enouth lube for my 1862 Navy Colt?
salvadore is offline  
Old February 7, 2011, 11:38 AM   #2
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,392
Lee Alox lube is for smokeless powder. If you talking about one of these:

Images courtesy of Lee Precision
You should be using a black powder lube or pre lubricated wad.
zippy13 is offline  
Old February 7, 2011, 11:57 AM   #3
sewerman
Senior Member
 
Join Date: December 30, 2005
Location: hurricane alley, florida
Posts: 304
many people experience good luck with conicals in B.P. pistols.
especially in the ROA pistols.


i have had better luck with a .454 ball as noted by many others on the forum. as for lube any natural fat product mixed with beeswax is good.
many use crisco and parafen based wax. but regular lubes & oils used with smokeless powders tend to harden up , crud out if you will , with the b.p. fouling.

the key to using a conical is to keep them straight in the cylinder when loading.

s.m.
__________________
"When the government fears the people, there is liberty. When the people fear the government there is tyranny!" Thomas Jefferson

"They that can give up an essential liberty to obtain a little temporary safety, deserve neither liberty nor safety!" Benjamin franklin

The Armed Citizen PREVENTS tyranny!
sewerman is offline  
Old February 7, 2011, 12:29 PM   #4
junkman_01
Junior member
 
Join Date: November 9, 2010
Location: Florida
Posts: 260
Most C&B revolvers get better accuracy with round balls and moderate powder charges.
junkman_01 is offline  
Old February 7, 2011, 12:39 PM   #5
freedom475
Senior Member
 
Join Date: November 18, 2008
Location: Rocky Mountains of Montana
Posts: 247
I think you will hate yourself after using the Alox... on a good note, it is pretty easy to get off with acetone or minral spirtis.... as others have said, the best thing for BP is natural oils/lube... I use "Skidmore's Leather stuff now, since I buy it by the gallon for my business and it is cheaper than bore-butter... and doesn't get Nasty and Smelly like crisco based stuff.

I tried cones for a while and found the they were too hard for me to get loaded proper.. so I went back to RB's
__________________
Maker of Horse Tack and Cowboy Gear.
www.7xleather.com

Mister, why do you carry a 45? "Cause Sam Colt don't make a 46."
freedom475 is offline  
Old February 7, 2011, 08:34 PM   #6
Hawg Haggen
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,650
Lee conicals are easy to load straight because they're tapered. I'd get rid of the alox and use beeswax or a beeswax/crisco mix.
Hawg Haggen is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:47 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07487 seconds with 9 queries