The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Lock and Load: Live Fire Exercises

Reply
 
Thread Tools
Old January 22, 2011, 06:13 PM   #1
WANT A LCR 22LR
Senior Member
 
Join Date: September 5, 2010
Posts: 389
Using rubber conveyor belting as partial backstop?

Would shooting at rubber CV belting be a ricochet hazard?

The indoor pistol range at a gun club uses the typical angled steel and trough below to catch bullets but has 1/2" thick conveyor belting just behind the targets. I'm guessing the belting is used to prevent / limit a bullet from ricocheting off the backstop towards the shooter. Some of the belting has a pretty big hole worn through behind the target, other places have bullets 1/2 stuck through the belt ( mostly 22 ) and there seems to be a fair number of undamaged jacketed round nose bullets that were fired but fell to the ground. ( 45 ACP )

The targets are stationary and the shooter must move down range to get a closer shot. ( not a issue as it's pretty much a self serve type deal and I've never came across others wanting to use the range at the same time )

This system has been in place for decades and seems to work. I want to make a similar setup for home use ( 38 +P at 21 ft ish distance ) but am wondering if belting is the best choice. I recently came across 3/8 thick and 3/16 thick belting so material is in stock. The whole mess will be mounted on a trailer for portability. I'm thinking of a shooting area 10 to 15 ft wide, 10 ft tall with wings that fold out at a 45* for a extra 3 ft per side / top. Fabrication isn't a issue.
WANT A LCR 22LR is offline  
Old January 28, 2011, 05:24 PM   #2
wogpotter
Senior Member
 
Join Date: September 27, 2004
Posts: 3,359
We put some heavy-duty industrial ones (from a quarry, so they are 3/4 thick) as safety berms at the firing line. When we tested the nylon reinforced belts a .22RF penetrated 3 layers & partially penetrated the 4th.
I'd take that into consideration when planning the installation.
They are heavy as all get out BTW, specially when lifting a 15' long section & holding it in place while attaching mounting hardware.
__________________
Allan Quatermain: “Automatic rifles. Who in God's name has automatic rifles”?

Elderly Hunter: “That's dashed unsporting. Probably Belgium.”
wogpotter is offline  
Old February 1, 2011, 01:45 PM   #3
JohnMoses
Senior Member
 
Join Date: April 11, 2008
Posts: 107
My indoor shooting tube is 30" in diameter & 52' long. The end is 2 thickness' of 1/2" conveyor belt, backfilled w/ sand. This makes the target convex. 45 auto, 38 spcl, 22s sometimes stick in the belting. Once, I had a 380 fmj roll to a stop by the shooting station. It was scuffed on 2 sides as it bounced down the tube. I think angling the belt @ 45 degrees would be a good idea.
JohnMoses is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07078 seconds with 9 queries