The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old December 9, 2010, 11:46 PM   #1
Boweevil23
Junior Member
 
Join Date: November 9, 2010
Location: Sylvester, GA.
Posts: 11
Remove Blueing Salts "Bloom"

I have an old pump "take down" shotgun that was hot blued about 25 years ago and it appears that it was not rinsed well enough or not rinsed with the correct solution. It has "bloom" (I think that's the correct term) coming from around the barrel adjusting bushing in the receiver. This bloom has the bushing frozen and will not turn. I have had it soaking in Kroil for a couple of days and it dosen't appear to be having any effect. Any suggestions on what I could use to disolve this stuff without affecting the blueing??
Boweevil23 is offline  
Old December 10, 2010, 08:49 AM   #2
Goatwhiskers
Senior Member
 
Join Date: April 8, 2009
Location: Batchelor, La.
Posts: 464
I don't THINK it's "bloom" after 25 years and the 'smith probably wouldn't have blued it with the bushing in place anyway. I would suggest that you don't get in a hurry, use a 50/50 mixture of acetone and ATF (beats the heck out of anything else I have used) and use a heat gun to make the thing turn loose. It will probably take plenty of soaking and several applications of heat to get it to turn loose. Another thought, you can heat the bushing with the heat gun and then apply ice to the barrel next to the bushing--can help to make the barrel shrink away from the bushing and break the bond. When it comes loose clean the heck out of the parts and apply a little never-seize, end of problem. Goatwhiskers the Elder
Goatwhiskers is offline  
Old December 10, 2010, 01:30 PM   #3
Boweevil23
Junior Member
 
Join Date: November 9, 2010
Location: Sylvester, GA.
Posts: 11
Goatwhiskers. Thanks for the reply. I should have elaborated a bit more. The barrel is removed from the receiver. I have another barrel that I want to swap onto the receiver for quail hunting but when installed it has a small amount of loose motion side to side, so I need to adjust the bushing in a tad.
I struck and polished the whole gun many years ago and took it to the local "Smith" (I use the title loosely) to have him do the dip. (I had sold my hot blueing equipment at that time due to the fumes rusting everything in the neighborhood and safety concerns (nasty little blisters if it splattered on you). Anyway, when I picked up the gun, the bushing was in place, in the receiver, and I thought that he had removed and replaced it. The gun has sat in the back of the closet until recently. When I decided to change barrels and use the gun I found that the bushing was frozen in place with the bloom oozing out from the threads. Just a bit of explination, I suppose the cure would still be as you suggested?
Boweevil23 is offline  
Old December 10, 2010, 01:35 PM   #4
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,431
Try the oil and acetone solution, see if it works. FWIW, the salts have crystallized in the threads and effectively locked the parts together, then rust takes over and helps make it worse.

Heat from a propane torch will break up the salt crystals and the rust, but be careful or you will discolor the bluing.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old December 10, 2010, 08:43 PM   #5
gyvel
Senior Member
 
Join Date: August 30, 2009
Location: Northern AZ
Posts: 5,229
Your best bet is to go to your local health food store and buy a bottle of "100% PURE, NATURAL wintergreen oil." (Not the stuff at Walgreen's.) This has proven to be the most powerful penetrant I have ever used. The late Clarence M. Bates put me on to this. Use it sparingly, as a little bit goes a long way.
gyvel is offline  
Old December 11, 2010, 04:14 PM   #6
govmule84
Senior Member
 
Join Date: December 15, 2005
Location: Up on a hill
Posts: 398
Common old brake fluid works very well, too.

I've heard guys swear by...

wait for it...

water. Swear to God, I've been told it's the bee's knees for getting rusted stuff out. Never tried it myself, but been told it by enough reliable fellas that I would try it.
govmule84 is offline  
Old December 11, 2010, 10:48 PM   #7
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,320
Boil the heck out of it in distilled water. Oil won't do the job.

Jim
__________________
Jim K
James K is offline  
Old December 13, 2010, 11:00 PM   #8
Boweevil23
Junior Member
 
Join Date: November 9, 2010
Location: Sylvester, GA.
Posts: 11
Thanks to all. I apperciate your help.
Boweevil23 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:49 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07900 seconds with 9 queries