The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 25, 2010, 08:41 AM   #1
tpcollins
Senior Member
 
Join Date: February 18, 2009
Location: SE Michigan
Posts: 443
Does this Burris ring look right to you?

Based on the recommendations from this forum, I bought Burris Signature rings to mount an AV 3x9x36 Swarovski on a new T/C Bone Collector ml. While on stand last week I looked down and saw the top of the rear ring was tilted forward.

I took some pics and forwarded them to Burris and got a response from a guy that thought the rings were doing as intended. Not satified with his response, I was about to elevate the concern when he said he would send me a replacement ring. I'll admit this pic is a bit better that the original ones sent but does anyone else think there's something wrong with it or could I have possibly mounted it wrong? I used a Fat Wrench to torque the screws down and my other 3 Sig rings look perfect. Thanks.
Attached Images
File Type: jpg IMG_0102.jpg (129.2 KB, 124 views)
File Type: jpg IMG_0103.jpg (115.4 KB, 103 views)
__________________
What direction did that last shot at Kennedy come from?
tpcollins is offline  
Old November 25, 2010, 10:55 AM   #2
rickdavis81
Senior Member
 
Join Date: April 3, 2006
Location: Missouri
Posts: 398
I've had several and they didn't look like that. Is the insert just pushed out to far on one side? Can you loosen it and align the insert and retorque them? I think it's an insert problem.
rickdavis81 is offline  
Old November 25, 2010, 11:22 AM   #3
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,631
There is a problem !!!

There was a previous post that had an identical symtom. In this case and with what I am looking at, I'd say that there is a problem. However, I'd only be guessing as to what is causing it. Will add that the rings you have are quality rings, by my measure. I don't like hte position of the inserts but really can't say what is happening. For now, I'd suggest breaking it down and starting all over. ......



Be Safe !!!
Pahoo is offline  
Old November 25, 2010, 12:15 PM   #4
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,342
The gap should be even.

Either the ring is bad, there is debris between the ring and scope, a shim is wrong, or even the bell of the scope for the turret is not even around the scope.
brickeyee is offline  
Old November 25, 2010, 05:20 PM   #5
hooligan1
Senior Member
 
Join Date: July 18, 2010
Location: Independence Missouri
Posts: 3,334
What the?? What's the extra looking piece under the ring in the second pic?, I have some burris rings and they don't seem to have that many parts. Hell send them back and get Leupold rings and explain to them why.
__________________
Thanks for coming!
hooligan1 is offline  
Old November 26, 2010, 10:35 AM   #6
guncrank
Senior Member
 
Join Date: July 15, 2006
Location: Fern Creek ,KY and Metro Louisville at large
Posts: 319
No that's not right.
As already stated loosen up ring and push insert back under ring half.
If it moves again then you have a bad ring half.
CEW
__________________
CW Shooters Supply Inc
1-866-217-5990
Machine Shop and Finishing Services to the trade and public
guncrank is offline  
Old November 26, 2010, 12:08 PM   #7
hoghunting
Senior Member
 
Join Date: March 27, 2006
Posts: 1,353
I'm willing to bet the replacement ring will fit exactly like that. It appears the front of your base is lower that the rear - by the angle of the lower half of the front ring. I agree with the Burris rep that the rings are doing exactly as they are supposed to do. If you use a different type of ring, you will need to shim the front of the base in order to keep the reticule centered in the objective lens.
hoghunting is offline  
Old November 28, 2010, 10:12 PM   #8
guf
Member
 
Join Date: May 25, 2010
Posts: 34
burris signature ring

tpcollins: there's nothing wrong with the ring. the upper ring is not aligned with the insert.
guf is offline  
Old December 1, 2010, 12:32 AM   #9
publius
Senior Member
 
Join Date: January 25, 2005
Location: Mississippi/Texas
Posts: 2,453
The ring appears to have been tightened with the insert not directly under the top half. Take it apart and try again. P.S., I really like the rings, they do a great job of correcting minor mounting problems and manufacturing variances.
__________________
"Suppose you were an idiot, and suppose you were a member of Congress, but I repeat myself." Mark Twain
publius is offline  
Old December 1, 2010, 04:13 AM   #10
Win_94
Junior member
 
Join Date: August 21, 2010
Location: Ohio
Posts: 214
It looks as if the screw head is angled, or the screw is cross threaded or the ring hole is angled where the screw head rests.

The inserts promote even contact, so I would bet there is no binding from the angled ring on the scope.

The ring isn't as "intended" though.
Win_94 is offline  
Old December 1, 2010, 10:48 AM   #11
Horseman
Senior Member
 
Join Date: February 1, 2006
Location: Midwest
Posts: 1,065
I'd take the top off and try again. Rotate the insert around to make sure it's free fitting in the bottom half before reinstalling the top. Be carefull to keep the insert centered under the top as you tighten and I think it'll go back straight.
Horseman is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09041 seconds with 10 queries