The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 17, 2010, 09:01 PM   #1
smurfsdad
Junior Member
 
Join Date: November 9, 2010
Posts: 8
Old rifle cleaning advice needed

I've come upon an old Mossberg Model 46b-b that is pretty rusty and dirty.
I've got the stock off to clean and finish. I've cleaned most of the metal pretty well but have a few areas that I'd just as soon not take apart fearing that I'd screw something up. Mainly the trigger and bolt action areas. These places are not rusty, but are dirty and may have bits of steel wool in them. Can you guys recommend any solvent spray to use in order to flush these areas clean?
Thanks for your time
smurfsdad is offline  
Old November 17, 2010, 10:09 PM   #2
DnPRK
Senior Member
 
Join Date: August 24, 2001
Location: LC, Ca
Posts: 1,760
The old Mossbergs are steel. I use 14 ounce spray cans of CRC's Brakleen automotive brake cleaner from Auto Zone. It blasts away all the gummy dirt and dries quickly. Use it in a well ventilated area.
DnPRK is offline  
Old November 18, 2010, 02:37 AM   #3
Bill DeShivs
Senior Member
 
Join Date: April 7, 2006
Posts: 7,010
Brake parts cleaner is the way to go.
Make sure you lube thoroughly after using it. My routine is to use brake cleaner, then flush with WD 40 to lube internal areas and displace any condensation caused by the brake cleaner. Dry, then oil.
__________________
Bill DeShivs
www.billdeshivs.com
Bill DeShivs is offline  
Old November 18, 2010, 10:45 PM   #4
smurfsdad
Junior Member
 
Join Date: November 9, 2010
Posts: 8
Thanks guys for your input
smurfsdad is offline  
Old November 24, 2010, 05:08 PM   #5
dutchy
Senior Member
 
Join Date: May 30, 2005
Location: Holland
Posts: 196
cleaning

I have cleaned many old guns, including a lot of rimfires.
My recipe to get the goo out is: strip as much as possible and then soak and brush with a clean paintbrush in white spirit. After thorough cleaning apply Ballistol generously and you do not need to look at the action for a long time.
After shooting only clean affected areas.
In case of an unlacquered (= not sealed) stock:
Strip of all metal parts, get an electric paint remover and, finding out the right distance to the wood, (start with a larger distance and work closer from there) and make the muck sweat out. Regularly remove muck with clean preferably old cotton cloth. When ready apply oil to your taste.
Dents are taken out by covering with very wet cotton cloth and applying the electric iron very briefly to on top of the cloth on the dent.
PS: White spirit is a hydrocarbon. That means: outside or at least in a very well ventilated space and eliminate all ignition sources.
dutchy is offline  
Old November 25, 2010, 07:30 PM   #6
gunney 67
Member
 
Join Date: July 21, 2008
Location: boise idaho
Posts: 77
remember to use good quality rubber gloves(cheap ones dissolve) when using brake cleaner. It ain't good for your liver. Well- ventilated is also a good idea.
gunney 67 is offline  
Old November 26, 2010, 12:00 AM   #7
Bigfatts
Senior Member
 
Join Date: December 20, 2005
Location: Lutz
Posts: 1,493
While you're at it, there is plenty of excellent info on your rifle here:
http://www.rimfirecentral.com/forums...splay.php?f=51
Bigfatts is offline  
Old November 26, 2010, 09:19 AM   #8
Rifleman1776
Senior Member
 
Join Date: April 25, 2010
Location: Arkansas
Posts: 3,309
Spray carburetor cleaner has long been my top cleaning tool.
Rifleman1776 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:43 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09941 seconds with 9 queries