The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 8, 2010, 08:51 PM   #1
Hiram33
Junior Member
 
Join Date: November 8, 2010
Posts: 3
9 mm lead vs. plated or fmj

Just started with my new dillon 550b loading 9mm. where can I find load and pressure data that compares lead cast bullets vs. plated or fmj.

looking at: Berry 115 grn. plated rns / with 6.0 grn Power pistol / winchester primers.

Any direction or advise would be appreciated.

Thanks
Hiram33 is offline  
Old November 9, 2010, 07:20 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
Back down that Power Pistol load to a start of 5.4g for those Berrys, and see how the accuracy looks from your launch platform.

(Work up in .1g increments for accuracy.)
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old November 9, 2010, 08:10 AM   #3
spacecoast
Senior Member
 
Join Date: October 14, 2009
Location: Sunshine and Keystone States
Posts: 4,133
If you're using Berry's plated bullets, then use low to mid-level FMJ data and you will be fine.
spacecoast is offline  
Old November 9, 2010, 08:55 AM   #4
demigod
Junior member
 
Join Date: March 13, 2008
Location: AZ
Posts: 1,129
I use full powered loads with my berry's plated 9mm. I'm running them in a glock, and the pistol doesn't care for mild loads. Full powered 9mm loads are within the max velocity for plated bullets.
demigod is offline  
Old November 9, 2010, 10:18 AM   #5
COSteve
Senior Member
 
Join Date: September 6, 2009
Posts: 473
The plated bullets thinner copper cover than a jacketed bullet (about .007") coupled with their softer lead cores allows them to obturate into the rifling much like plain lead bullets which is why most manufacturers recommend you use lead bullet loading data to avoid exceeding max pressure limits. In addition, while most manufacturers recommend a max velocity of about 1,200fps when using plated bullets, my personal testing has confirmed that they hold together just as well as jacketed bullets at much higher velocities when loaded correctly.

I've shot many thousands of 165grn 40/10mm Berry's, Rainiers, X-Treme, and Speer Gold Dot bullets (yes, they are also plated) at velocities over 1,500fps out of my 6" custom 10mm G20L with good accuracy and no problems. In addition, I've shot a thousand or so Rainier plated 110grn M1Carb bullets at over 1,900fps without issue too. The secret to loading plating bullets is to refrain from over crimping them. Just remove the flair in the neck and rely on the neck tension to hold the bullet and you'll do just fine with them.
__________________
Steve

“Remember, no matter where you go, there you are.” - Buckaroo Banzai 1984
"When you find a find a big kettle of crazy, it's best not to stir it." - Dilbert 2009
COSteve is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:43 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06746 seconds with 9 queries