The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 16, 2010, 07:34 AM   #1
gotigers
Senior Member
 
Join Date: April 30, 2009
Location: Memphis
Posts: 353
Can a cut down 1100 barrel be threaded?

Can a cut down 1100 barrel be threaded for chokes? I have a 28" that i want cut down to 22", but cyl bore may just not suit my needs. I would like it threaded. Is this possible. Or....would i be better off selling this barrel and buying a new 22" threaded barrel?
gotigers is offline  
Old August 16, 2010, 08:52 AM   #2
davecharles
Member
 
Join Date: January 3, 2010
Location: Carbondale
Posts: 60
Well the real answer is.... some can and others can't. I've cut off some Remington barrells (other manufacturers as well) to find the bore off center and the wall too thin one one side to thread. Many others I have done are nearly centered and can be threaded just fine. Good luck.
Dave
davecharles is offline  
Old August 16, 2010, 01:39 PM   #3
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,507
Like davecharles said, there isn't just one answer.

* Older 1100 barrels are very thin, and there is not always enough metal to just bore/thread for chokes. These can sometimes be swaged out to allow for threading, but there are other issues that may prevent it (hard spots, out of round, off center, brazed ribs, barrel lugs, etc).

* Briley can thread for their thin choke tubes, but it will cost you the same or more than a new barrel.

* You could also have the shortened barrel backbored to give you a choke constriction, but finding a smith that can do it may be hard.

* Threaded 22" 1100 barrels are easy to find, and take easy-to-find choke tubes. Here's one.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old August 16, 2010, 07:38 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,852
They still make exterior chokes, which require turning down the barrel, but don't involve any threading. They also make a choke adapter that attaches to the barrel the same way (solder) but is threaded for interior choke tubes.

Jim
__________________
Jim K
James K is offline  
Old August 16, 2010, 10:27 PM   #5
GunCat
Member
 
Join Date: December 27, 2008
Location: Western, KY
Posts: 41
Measure the outside diameter of your barrel at the spot you plan to cut it. An OD of at least .845” is required for 12 ga Rem-Choke tubes, .825” for Tru-Chokes, or .805” for Tru-Choke “Thinwall” tubes.

All these minimum diameters are based on the bore being concentric with the outside of the barrel. If the bore if found not to be concentric then your gunsmith will have to measure the actual barrel walls to determine if adequate thickness is there for safe threading..
__________________
Hardships are quickly forgotten. Intense heat, bitter cold, rain and snow, fatigue, and luckless hunting fade quickly into memories of great fellowship, thoughts of beautiful country, pleasant camps, and happy campfires.
Fred Bear 1902-1988
GunCat is offline  
Old August 17, 2010, 06:59 AM   #6
gotigers
Senior Member
 
Join Date: April 30, 2009
Location: Memphis
Posts: 353
Quote:
Scorch

.........

* Threaded 22" 1100 barrels are easy to find, and take easy-to-find choke tubes. Here's one.
Yeah, i saw that. $229 is more than i want to spend. I only spent $310 on the 1100. A local smith would cut mine down and thread it for $110, but it just doesnt sound like the way i want to go.

I have a lead on a used 22" threaded barrel locally for $145. I will see it later this week. If it is in usable shape, i will get it. It is actuallyhard to find them used. I have been looking constantly online, calling local, etc for a week. I found this one and one online.
gotigers is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 05:13 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07351 seconds with 9 queries