The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 31, 2000, 10:46 AM   #1
Waitone
Senior Member
 
Join Date: March 19, 2000
Posts: 2,904
Shortly I will begin reloading. I am looking for plans to a reloader's workbench. I could use a standard workbench plan but my guess is it would be short on cabinets, drawers, etc.

Anyone out there know of plans to a reloader's workbench.

Many thanks in advance


------------------
Extremism in the defense of liberty is no vice. Moderation in the pursuit of justice is no virtue.

Barry Goldwater--1964
Waitone is offline  
Old October 31, 2000, 11:06 AM   #2
DAL
Senior Member
 
Join Date: October 15, 1999
Location: Colorado Springs, CO, USA
Posts: 653
Waitone, try the following site. This guy, I believe he posts here under the name SKR, has one heck of an in-depth site on reloading. Toward the bottom of the page, he has plans for a reloading bench. Give it a look and see what you think. http://www.again.net/~steve/table3.html
DAL

------------------
Reading "Capitalism: The Unknown Ideal," by Ayn Rand, should be required of every politician and in every high school.

"Guard with jealous attention the public liberty. Suspect everyone who approaches that jewel. Unfortunately, nothing will preserve it but downright force. Whenever you give up that force, you are ruined."
--Patrick Henry, during Virginia's Convention to Ratify the Constitution (1788)

GOA, JPFO, PPFC, CSSA, LP, ARI, NRA

[This message has been edited by DAL (edited October 31, 2000).]
DAL is offline  
Old October 31, 2000, 11:33 AM   #3
Waitone
Senior Member
 
Join Date: March 19, 2000
Posts: 2,904
<BLOCKQUOTE><font size="1" face="Verdana, Arial">quote:</font><HR>Originally posted by DAL:
Waitone, try the following site. This guy, I believe he posts here under the name SKR, has one heck of an in depth site on reloading. Toward the bottom of the page, he has plans for a reloading bench. Give it a look and see what you think. http://www.again.net/~steve/table3.html
DAL

[/quote]

Thanks

Waitone is offline  
Old October 31, 2000, 01:19 PM   #4
Guy B. Meredith
Senior Member
 
Join Date: August 29, 1999
Location: Salem, Oregon
Posts: 1,578
Try http://www.reload-nrma.com/ for a set of plans.

I bought the $99 Gorilla GR1901 workbench, put a 3/4" plywood sheet on top the bench's particle board top and bolted them both down. Works well despite my concerns about the keyhole style connectors holding everything together.
Guy B. Meredith is offline  
Old October 31, 2000, 09:49 PM   #5
PoiDog
Senior Member
 
Join Date: September 1, 1999
Location: IL
Posts: 219
I bought the plans from NRMA and built the bench late last year. It is outstanding, the final product is very stout and heavy. I thought I would have to bolt it to the garage wall to give it stability. Not necessary, it is rock solid without any extra bolts. I built it to the height in the plans since I like to decap and resize standing up. I'm about 6'2" so it works for me. People of shorter stature would probably cut down the leg size appropriately. Recommended.
PoiDog is offline  
Old November 1, 2000, 10:33 AM   #6
Coolray
Senior Member
 
Join Date: August 10, 2000
Location: Spokane ,wa
Posts: 290
If you have a Costco near you thay have a great hardwood bench 6' long with shelves and cabnets and drawers for under $200 and it is very sturdy. All hardwood construction.
Coolray is offline  
Old November 2, 2000, 06:47 PM   #7
labgrade
Member In Memoriam
 
Join Date: November 29, 1999
Location: west of a small town, CO
Posts: 4,346
For a cheap alternative to any planned things ... I got ahold of a solid core door, screwed a 2X4 to its bottom back which is lagged into wall studs. Two "feet" = 4X4s up front finish it off.

"Luckily," an old chest of drawers we had lying around provides all the drawers I need & slips right under the whole deal. As the top of the chest is about 10" lower than the bottom of the bench, I get another layer of storage.

An old water bed headboard up against the wall gives more storage space up above & as an added benny, I get to watch myself reload in the mirror.

Not much to look at (me or the set-up ) but cost about $10 all told, is sturdy as a rock & purely functional.
labgrade is offline  
Old November 3, 2000, 03:17 PM   #8
jtduncan
Senior Member
 
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,681
Go to GlockTalk and ask. A couple of good bench plans there. You can get scrap wood from contruction sites if you ask the foreman and for the price of some wood nails, you can have a nice 3' x 7 or 2' x 8' bench for less than $10.

Don't buy one, that's your powder, bullets, and primer, and equipment money.

------------------
The Seattle SharpShooter - TFL/GT/UGW/PCT/KTOG
jtduncan is offline  
Old November 3, 2000, 03:52 PM   #9
Westtexas
Senior Member
 
Join Date: April 1, 2000
Posts: 293
In Dillon's Blue Press, they have a neat-looking bench kit that looks sturdy and has a backboard with shelves, etc. Looks good. Anyone have any experience with their benches?
Westtexas is offline  
Old November 5, 2000, 10:24 PM   #10
The specialist
Senior Member
 
Join Date: January 10, 2000
Location: boston,MA,USA
Posts: 237
I bought a bolt together bench made of 2x6's at grossmans bargain outlet for 29.99 and lag bolted it to my cellar wall. I use an old desk for storage of tools and supplies.
The specialist is offline  
Old November 6, 2000, 02:44 PM   #11
doc-lav
Junior Member
 
Join Date: November 6, 2000
Posts: 2
I bought the "Sturdy Bench" listed in the Dillon Catalog and have excellent experience with it. Since I'm in a wheelchair I like the sliding lower work place and the versitility of the design.
doc-lav is offline  
Old November 6, 2000, 09:03 PM   #12
twist996
Member
 
Join Date: October 20, 2000
Posts: 85
made my own, but i own the lumber yard: 3/4" top, measures 36" x 96". double 2x4 legs, cut to my tastes. wouldn't cost much, if you wanted to by the material....can e-mail a better parts list, but not right now...

------------------
speak now, or forever hold your peace
twist996 is offline  
Old November 7, 2000, 01:06 PM   #13
Marshal
Member
 
Join Date: October 23, 2000
Location: Buda, Texas
Posts: 83
I use an old library table I acquired many years ago. It's strong enough to hold an elephant, and has nifty drawers under the top. I used lag screws on the press though, because machine bolts through the table would interfere with the drawers, and I didn't feel like lying on my back to counter sink the ends.
Marshal is offline  
Old December 7, 2000, 09:50 AM   #14
seadog
Senior Member
 
Join Date: October 27, 2000
Location: Virginia
Posts: 287
My dad was a woodworker and did furniture, etc. When I got into reloading about 15 years ago, I asked him to build me a bench. He called me over a few weeks later and showed me a masterpiece made out of solid ash top about 1 1/2" thick, biscuit joined like butcher block. Solid oak legs. Marine Grade plywood bottom shelf and a couple of small drawers. It was about 51/2 feet long and 30" deep. Ash is baseball bat wood...it's d**n hard and heavy. I told him before he made it not to go to too much trouble...When I saw it I said,"What a masterpiece". It's heirloom quality and I think of him every time I'm at it... A lucky son...
seadog is offline  
Old December 7, 2000, 12:05 PM   #15
Steve Smith
Senior Member
 
Join Date: December 9, 1999
Posts: 4,131
A local liquidator company bought the contents of a large electronics manufacturing plant. I bought an electronics tech desk (blue painted steel, white formica top) for $65. It has a 5' wide, 3' deep, 2" thick wooden top (with the aforementioned formica covering), adjustable steel legs, a footrest, a 10 outlet industrial power strip across the back, a 5' wide, 1' deep shelf, a 5' long double row florescent light, and a 5' accessory rail specifically built for--get this--Acro-Bins! I recently priced out my desk from a supply house...the desk would have cost over $1000 brand new and equipped the same. I'm so happy with this desk...and I've been able to help a few friend get some too.
Steve Smith is offline  
Old December 7, 2000, 08:40 PM   #16
slickpuppy
Senior Member
 
Join Date: August 29, 1999
Posts: 928
Lots of great replies here. I picked up a 6 foot length work bench kit with lower shelf from Home Depot for $49.95. I looked other alternatives over before purchasing it and by the time I bought the lumber, cut it to size, and bought the requisite hardware, the kit was a better deal.
slickpuppy is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:01 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09872 seconds with 9 queries