The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 4, 2000, 02:45 PM   #1
Dubletap45
Member
 
Join Date: October 1, 2000
Posts: 28
I was at the range yesterday playing with a couple of friends after an IPSC match. We were shooting clay targets we placed at 50 yds. I noticed that my .44special loads were really dirty compared to my friends factory .38 Special PMC. My S&W629 was covered in black residue while his was relatively clean. I loaded a 205 cast bullet on top of HS-6 (can't remember the charge off the top of my head, but it was most likely the max out of the lee manual). The PMC was jacketed so some of the residue was probably lead but all of it? Does anyone use a different powder in a large bore pistol, with commercial cast bullets with cleaner results? Any advice is appreciated.

DT45
Dubletap45 is offline  
Old December 4, 2000, 03:02 PM   #2
jtduncan
Senior Member
 
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,681
For that larger case, TiteGroup was developed. Clean and accurate!
__________________
The Seattle SharpShooter - TFL/GT/AR15/SGT/PCT/KTOG/SWF/RF/HKPRO/OA2/1911Forum
Reloaded .223 Rem, 9mm, 40SW, 357 SIG, 10mm, 44 Spl, 44 Mag, 45 ACP Today?
jtduncan is offline  
Old December 4, 2000, 05:41 PM   #3
Poodleshooter
Senior Member
 
Join Date: August 7, 2000
Location: Floating down the James River in VA
Posts: 2,541
Crimping tighter with the medium speed pistol powders designed for moderate loads (Unique and the HS powders) can help to some degree, but in the end if you want clean powder, you have to pay the money for the newer powders.
Poodleshooter is offline  
Old December 4, 2000, 09:36 PM   #4
Archie
Senior Member
 
Join Date: May 26, 2000
Location: Hastings, Nebrasksa - the Hear
Posts: 2,096
I use W231 for about all my pistol rounds. It meters well and burns cleanly. About the only thing it doesn't do well is the heaviest 357 and 44 Magnum loads and such. Propably 10mm top end stuff would require a slower powder also.
For most any "regular" loads, W231 does very well.
__________________
There ain't no free lunch, except Jesus.
Archie

Check out updated journal at http://oldmanmontgomery.wordpress.com/
Archie is offline  
Old December 6, 2000, 09:20 AM   #5
Quantrill
Senior Member
 
Join Date: February 28, 1999
Location: Arizona, USA
Posts: 725
Clean burning pistol powder

I have always been pleased with 700X for an accurate and clean powder for target pistol loads. Quantrill
Quantrill is offline  
Old December 6, 2000, 01:07 PM   #6
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,648
Black redidue???????????????????

Dubletap45. I'm willing to bet that the black residue came from the lubricant on the cast bullets you were shooting, and not the powder. That is one of the drawbacks of shooting cast lead in handguns. I run into the same thing with my 624 .44 Spl. and my .44 Mags. I never shoot jacketed bullets in them, so I have lots of cleaning to do at the end of a session.
Paul B.
Paul B. is offline  
Old December 6, 2000, 07:06 PM   #7
Swamp Yankee
Senior Member
 
Join Date: November 26, 2000
Location: Northeastern Ct.
Posts: 1,013
I agree with Paul B. The sizing lubricant really cruds up a gun quickly, especially stainless steel. Be sure to clean your gun after each range session. Pay close attention to ejector rod and cylinder bore. The fit there is tight and I've had problems with burned lubricant getting in there and gumming up an otherwise smooth action.
As for clean burning powders my experience is Bullseye, W231, and PowerPistol are all very clean burning.
Check the Blue Press from a couple of months ago, I believe they had an article on this subject.
Swamp Yankee is offline  
Old December 6, 2000, 07:57 PM   #8
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
For a Unique (pun) alternative highly recommend clean-burning Hodgdon Universal Clays. Cleaner than HS6. Slower than W231.
Excellent in 44 Special (and every medium revolver load).

Clean and easy-metering.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:58 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07012 seconds with 9 queries