The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 2, 2000, 01:15 AM   #1
char923
Senior Member
 
Join Date: February 18, 2000
Location: Anchorage AK
Posts: 237
Does anyone have a Redding Competition seater die and how good and accurate are they.
char923 is offline  
Old December 2, 2000, 06:11 AM   #2
JMC
Senior Member
 
Join Date: March 6, 1999
Location: FL
Posts: 792
Redding Seater Die

I recently purchased two, one in .45-70 and one in 9mm Luger.

To be brief, they are great. I intend to order another in .40S&W shortly.

I use mine in a manner that one of the Redding techs suggested after I could not figure out how to return the mic to "0" after adjustment.
After I get my setting for a particular bullet, I write it down. I keep this slip of paper in the die box. Then, I can adjust the micrometer up or down from there according to bullet style/length, etc. A simple check with a digital caliper to be sure and your done.

I intend to start a small log book just for this procedure. Between myself, my son and son-in-law, we load 4 different 9mm bullets alone. This will make the process much easier and faster.

For the 9mm I was using the Dillon seating die and did not care for the trial and error method of bullet seating that it affords. The Redding die works very well in the 550B press.

No more turning, guessing and numerous adjustments as to COL!

Midway had the best price when I bought my 2 dies. The list is $75.00 and they get, I believe, $51.99 w/shipping.
__________________
Jim - NRA Life Member since '69.
JMC is offline  
Old December 2, 2000, 07:19 PM   #3
umstud
Member
 
Join Date: July 19, 1999
Posts: 31
JMC, the Redding competition die is absolutely worth the money. I shoot IPSC and am very meticulous about getting very precise oal. I make sure that the cases and bullets I use are of consistent length and am able to get all my rounds to within .002" of the desired oal using the Redding die. I also ditched all my other Dillon dies and replaced them with a set of reddings. The case sizing and deprimer die is much better than the Dillon. The Dillon has a wider bell at the opening of the die and if you use once fired brass especially those that have been shot from a glock, the sizing does not go all the way down to the bottom of the case. This will cause you to end up with a lot of rounds which will not pass the case gauge test. Try the redding you will love them. stud
umstud is offline  
Old December 3, 2000, 03:53 AM   #4
bk40
Senior Member
 
Join Date: January 12, 1999
Location: Mississippi
Posts: 1,004
The Redding is top quality and worth the price. One add'l benefit is it usually seats the bullet "straighter" reducing runout. The Forrester/Bonanza cmp seater is a little cheaper and works just as good.
bk40 is offline  
Old December 3, 2000, 04:23 AM   #5
char923
Senior Member
 
Join Date: February 18, 2000
Location: Anchorage AK
Posts: 237
Thanks guys for the info, I will pick one up.
char923 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06441 seconds with 9 queries