The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old June 17, 2010, 04:04 PM   #1
zcar75
Member
 
Join Date: December 3, 2009
Posts: 25
Not using a lubed wad

I am new to this. I have been shooting powder, wad, and ball with 30 grs of powder in my 1858 Rem .44 cal. Now, if I choose not to use the wad what happens to the space used by the wad in the chamber? This must mean that the ball is seated lower in the chamber. Is this OK? I just want to be safe.

Some shooters use 3 in 1 oil over the ball. Some just lube the ball in bulk before loading. From what I understad, the safest way is to put lube over the ball after loading such as chrisco and beeswax. Thanks for your help......
zcar75 is offline  
Old June 17, 2010, 04:15 PM   #2
surbat6
Senior Member
 
Join Date: March 22, 2010
Location: Northampton, PA
Posts: 164
As long as the ball is seated tightly against the powder and shaves a thin ring of lead at the edge of the chamber, you should have no troubles. For years, nobody used a wad when loading a cap and ball revolver. We smeared grease in the space in front of the ball. We thought we were preventing chain-fires, but what we were actually doing was keeping the fouling soft. I know it's messy, but after 43 years, I'm used to it.
I also use black powder only, not the newer powders.
__________________
I think of my gun as a tool for converting worthless human garbage into valuable fertilizer.
surbat6 is offline  
Old June 17, 2010, 04:17 PM   #3
Doc Hoy
Senior Member
 
Join Date: October 24, 2008
Location: Chesapeake, VA
Posts: 4,598
yup!

The ball just sits lower in the chamber. Someone may come in and recommend the addition of cornmeal but at 30 grains, I don't think you need it.

I don't use lube under the ball (between the ball and the powder) I put the lube over the ball.

I also lube the balls before loading by rolling them around in bore lube.

As far as the recipe for bore lube is concerned your post will generate a lot of responses. My personal lube is one toilet donut (the wax ring from under a toilet...I recommend buying new ones as the used ones leave a smell that masks the wholesome essence of black powder) to one pound can of Crisco. My recipe is a compromise because the toilet donuts no longer are made of natural products. And I really should be using lard rather than Crisco. Problem with lard is that it is too fattening. I used to shoot only .36s but now they are all .44s. I shifted to Crisco to try to get them back down to .36s.
__________________
Doc

My reading of history convinces me that most bad government results from too much government. Thomas Jefferson
Doc Hoy is offline  
Old June 17, 2010, 04:23 PM   #4
Hawg
Senior Member
 
Join Date: September 8, 2007
Location: Mississippi
Posts: 11,752
Do not use 3n1 oil for over ball lube. It makes cleanup a nasty job.
Hawg is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:07 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06903 seconds with 9 queries