The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old June 16, 2010, 05:53 PM   #1
tote4570
Member
 
Join Date: September 17, 2005
Posts: 30
rust on barrel

What is the best way to remove rust on the outside of the barrel of my 870 without messing up the finish too bad?
tote4570 is offline  
Old June 16, 2010, 06:36 PM   #2
noyes
Senior Member
 
Join Date: December 27, 2008
Posts: 1,032
Kroil
noyes is offline  
Old June 16, 2010, 06:43 PM   #3
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,341
On an 870 ....any old belt sander and a piece of 80 grit sandpaper ought to work just fine ..../and high speed is probably preferred / and then a rattle can of "krylon" ought to fix it ....

Seriously ( don't do that )... I'm just picking on my 870 buddies that seem to like em rusty and nasty and ugly looking ...

For a serious answer - I've used BoShield Rust Free ... on some of my woodworking tools ..when I screwed up and left some wet wood on a table top or something ... Its a quick acting product so I think it has the potential to help you out.

Whatever you do - go slow ... maybe test the product on a portion of the barrel under forearm / or where the barrel goes into the receiver - where its not noticeable first. I don't know if BoShield will attack a blued barrel or not ?? - but its a very good product. Many woodworking stores carry it ( for protecting cast iron table saw / joiner tops ...etc ....

Last edited by BigJimP; June 17, 2010 at 11:01 AM.
BigJimP is offline  
Old June 16, 2010, 06:50 PM   #4
Pahoo
Senior Member
 
Join Date: February 16, 2006
Location: IOWA
Posts: 5,587
On this one, there is more way to skin this cat. Kroil is good but there are certainly, no shortage of product that folks use on a regular basis. Lately, I have been using StrongArmBrand and you can google it as I have to order it on line. Great advice on going slowly.

Might I ask if this is a newer 870 Express.
Just asking. ....


Be Safe !!!
Pahoo is offline  
Old June 16, 2010, 07:14 PM   #5
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,406
Is your 870 an Express model with a matte black finish or a Wingmaster with a polished blue finish, or… ?
zippy13 is offline  
Old June 16, 2010, 07:51 PM   #6
tote4570
Member
 
Join Date: September 17, 2005
Posts: 30
Express model. I'm not trying to make it look like new, I'm just trying to get off the rust to keep it from getting worse.
tote4570 is offline  
Old June 16, 2010, 08:03 PM   #7
GrailKnight
Member
 
Join Date: April 8, 2010
Location: PA
Posts: 47
Buy a can of Barricade rust protection.
It does a great job on light surface rust and will not remove any blueing.

Here is a link to check out the product but I buy it from Gander Mountain.

http://www.cheaperthandirt.com/57208-1.html

The directions are on the can itself on how to use it to remove rust.
__________________
Who Dares Wins!
GrailKnight is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:23 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06288 seconds with 9 queries