The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old April 14, 2010, 07:21 PM   #1
87mustang
Member
 
Join Date: March 29, 2009
Posts: 91
mauser 98 question with pics

so i got this mauser 98 given to me. the barrel is a pitted mess, but the action seems to work smooth. the trigger is a piece of crap. i am looking for a 7mm mag for a toy. i don't care about it being a pretty gun, just one to shoot. i would prefer to use this stock if possible. what's a ballpark price to turn this gun into a 7mm mag? and is it worth it compared to buying something else?






Last edited by 87mustang; April 14, 2010 at 07:26 PM.
87mustang is offline  
Old April 14, 2010, 08:20 PM   #2
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
[what's a ballpark price to turn this gun into a 7mm mag?]

$450-$500, minimum - IF the action's long enough to handle the 7mm Mag (It doesn't appear to be)

A new barrel @ $225 minimum, unless a take-off can be located cheaper.
Enlarging bolt face for the belted case @ $50,
Fitting/chambering above barrel @ $150 +/_
Alterations to action/magazine to feed belted magnum cases @ $75-$100


[is it worth it compared to buying something else?] -

Not really (to me), but what price do you put on your pleasure/enjoyment ?

.
PetahW is offline  
Old April 15, 2010, 12:35 AM   #3
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,408
For the cost of conversion you could buy a factory rifle. Sell the beast to someone who needs a project.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old April 15, 2010, 07:22 AM   #4
87mustang
Member
 
Join Date: March 29, 2009
Posts: 91
so what is the ballpark value of this gun right now.
87mustang is offline  
Old April 15, 2010, 07:25 AM   #5
87mustang
Member
 
Join Date: March 29, 2009
Posts: 91
would this gun perform as well as a vanguard if it was converted?
87mustang is offline  
Old April 15, 2010, 07:42 AM   #6
mapsjanhere
Senior Member
 
Join Date: August 6, 2009
Location: Albuquerque
Posts: 2,344
Ballpark value for a sporterized 98 with a bad barrel probably $150 max. Look at ER Shaws website for prices on reasonable rebarrels. But even that route will not produce something more valuable than $350 - 400, and you can buy a new Howa/Vanguard for that. If you rebarrel than only for a caliber that is not commonly available for cheap as a new gun.
__________________
F 135 - the right choice
mapsjanhere is offline  
Old April 15, 2010, 08:24 AM   #7
kraigwy
Senior Member
 
Join Date: June 16, 2008
Location: Wyoming
Posts: 9,371
The action is long enough for the 7 Rem Mag.

Don't know about the price. SGNs has mauser actions you can get for $60-80 bucks, Boyds has some good reasonable stocks (Wood), as does MidwayUSA (plastic).

A barrel is gonna run you about $200. Plus another 200-250 to get it chambered and fitted to the action and open up the bolt face. Then you have to get it blued.

So its gonna cost you about $600 min. to put a gun together. You could shave that a bit if you do your own work, but then you still have to get a reamer and headspace gages.

So you can save a few bucks by buying new, or a good used rifle.

Personally I would rather build my own but I have the equipment to do it. Anyone can buy a rifle, not everyone can build one.....................Oh they can, but wont.

The problem with building your own, as you can see above, you are gonna pay $600 + (and it will probably be a big +), but when you're through, you will have a rifle you may be able to sell for maybe $350.

Thats why you dont find many rich gunsmiths out there.

The value of a home made gun isnt in the money you put into it.
__________________
Kraig Stuart
CPT USAR Ret
USAMU Sniper School Oct '78
Distinguished Rifle Badge 1071
kraigwy is offline  
Old April 15, 2010, 12:38 PM   #8
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,172
Deleted
__________________
Jim K
James K is offline  
Old April 15, 2010, 03:29 PM   #9
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,505
A rebarrel to 7x57MM would be a heck of a lot cheaper and would not need to do anything else to magazine, or bolt face, or to stock.
dahermit is offline  
Old April 21, 2010, 06:44 PM   #10
87mustang
Member
 
Join Date: March 29, 2009
Posts: 91
so if i got this gun into a 7mm mauser, what kind of money is required for that? and is brass readily available to handload?
87mustang is offline  
Old April 21, 2010, 07:29 PM   #11
dahermit
Senior Member
 
Join Date: October 28, 2006
Location: South Central Michigan...near Ohio, Indiana.
Posts: 3,505
http://www.midwayusa.com/browse/Brow...0766***9144***

About $83 bucks for a short chambered barrel. Yes, the brass is readily from the same source. Your would need a gunsmith to remove the barrel from the action, install the new barrel, finish ream the chamber and head space. This is the least expensive way to go (no other alterations to the existing action), and you end up with a 7mm that performs well and is pleasant to shoot.
dahermit is offline  
Old April 21, 2010, 08:01 PM   #12
87mustang
Member
 
Join Date: March 29, 2009
Posts: 91
so who in central ohio would be good at working on this gun?
87mustang is offline  
Old April 21, 2010, 09:01 PM   #13
PetahW
Senior Member
 
Join Date: September 19, 2008
Posts: 4,679
http://www.midwayusa.com/gunsmithlocator/home.aspx
PetahW is offline  
Old April 25, 2010, 09:28 AM   #14
Clark
Senior Member
 
Join Date: December 4, 1999
Location: WA, the ever blue state
Posts: 2,835

In Oct 2009 I built (3) 7mmRemMag rifles on Mauser actions, here is one of them:
A) Brazilian 7mm Mauser VZ24 action
B) Lothar Walther CM 1300 taper 7mm 26" Barrel blank weights 3 pounds 5 ounces = 53 ounces finished
C) Standard 7mmRemMag reamer, .45" drill, .47" boring bar in 4 step chambering
D) High Tech Specialties [Bansner] 20 ounce stock
E) Weaver #45 and #46 steel matte scope mounts
F) Limbsaver large recoil pad untrimmed
G) Oxpho Blue Cold Blue
H) TIG welded bolt handle
I) PAWS Aluminum bottom metal for Mausers weighs 3.5
ounces
J) Rear hump of trigger ground down and reduced trigger spring installed
K) Feed lips milled .51" Wide and 3.5" long
L) Bolt face opened to .532" with carbide tools on lathe and mill
M) Extractor claw relieved
N) Wooden plug epoxied into hollow cut off stock butt
O) Headspaced to .215", not SAAMI .220"
P) 3.25" wide sticky stretchy Vero Vennini strap
Q) Leupold VXII 2x7x33 scope
R) Stoney Point Target Knob
S) 34mm DVORAK INSTRUMENTS soft eye scope lens shade
T) Eagle Industries Shooter's Stock Pack [cheek pad]
U) Weaver quad lock 1" scope rings
V) Devcon steel putty epoxy under 1" of barrel, behind recoil lug, below tang, above bottom metal, under scope mounts.
W) Loctite 242 blue on scope mount threads
X) Rust-Oleum camouflage paint 1919 deep forest green on stock
Y) Stoney point objective lens cover

9 pounds without ammo.

65.5 gr H4350 162 gr Hornady SST moly 3.34", 3050 fps
0.75" group at 100 yards [1" high]
6.0" group at 440 yards [6.25 moa elevation adjustment] 5 mph wind


Here are the other two: stainless steel M70 take off barrel, Chrome Moly Rem700 take off barrel.
The rem shoots sub moa, the Win barrel shoots 2 moa.
Clark is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 06:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09118 seconds with 9 queries