The Firing Line Forums

Go Back   The Firing Line Forums > The Hide > The Dave McCracken Memorial Shotgun Forum

Reply
 
Thread Tools
Old March 20, 2010, 09:29 AM   #1
abs
Member
 
Join Date: April 26, 2006
Location: NJ
Posts: 88
help: can't assemble new o/u (cynergy)

Not sure if I connect receiver with barrels in a wrong way or don't lube enough.
I have Hoppe's 9 lubricating oil and break-free. What's the best for greasing the hinges? Thanks!
abs is offline  
Old March 20, 2010, 10:47 AM   #2
Ricklin
Senior Member
 
Join Date: February 22, 2008
Location: North Orygun Coast
Posts: 601
Quality grease

Use a good quality grease on the hinge pins, and on the hinge pin sockets where the pins fit in to the receiver.
Also a good film of grease on the metal portion of the forend where it contacts the receiver.

Is this not called out in the owners manual?
__________________
ricklin
Freedom is not free
Ricklin is offline  
Old March 20, 2010, 11:13 AM   #3
RoscoeC
Senior Member
 
Join Date: February 21, 2006
Location: DFW Metromess
Posts: 562
Ooops, Cynergy's don't have hinge pins. I had a little difficulty with it at first too. Grasp the barrels in the left hand (if right handed), with the vent rib under your knuckles. Grasp the action around the neck of the stock just behind the trigger guard. Place the arc of the receiver against the arc in the barrel block and slide the action upward while moving the barrels in the opposite direction. There will be some resistance as you compress the springs.

Hoppes is a cleaner and does little if anything toward lubrication. I use Mobile 1 synthetic grease available at your local car parts house. You may opt for some of the exotic and correspondingly expensive dedicated products, but I find the Mobile 1 to be quite adequate. It does not have Unicorn's earwax or other exotic ingredients, but it works well.

I wipe the receiver clean of the old grease after each range session, and apply new grease with a disposable flux brush.

I'm right there with Ricklin, RTFM (read that fine manual).
__________________
“Life is either a daring adventure or nothing." --Helen Keller
"Do not cry havoc when you should but hunt with modest warrant." --William Shakespeare
Glock Certified Armorer
NRA Life Member
RoscoeC is offline  
Old March 20, 2010, 11:59 AM   #4
zippy13
Senior Member
 
Join Date: August 23, 2008
Location: SoCal
Posts: 6,400
Grease is preferred over oil. Here's an extract from the Browning Owners Manual:

zippy13 is offline  
Old March 20, 2010, 12:16 PM   #5
abs
Member
 
Join Date: April 26, 2006
Location: NJ
Posts: 88
Thanks everyone, particularly Zippy: your pictures from manual have a better quality than my manual's ones...
abs is offline  
Old March 20, 2010, 03:28 PM   #6
olddrum1
Senior Member
 
Join Date: March 23, 2008
Location: Mid Missouri
Posts: 782
Whats the old saying "When all else fails, read the owners manual"?
olddrum1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:29 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07876 seconds with 9 queries