The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old November 28, 2009, 10:02 AM   #1
getupatree
Member
 
Join Date: May 4, 2009
Posts: 36
QR mount options for AR15 flat top. Advice needed

What are good mounts? I want a qr option. Do they need to be super high?
I am new to ARs and replacing the junk NC Star from earlier post with a Luepold mark AR scope. Probably 3x9x40. It has a 1 inch tube.

Need to spend 100 or less if possible. Ready to buy today

Thanks.
getupatree is offline  
Old November 28, 2009, 10:26 AM   #2
lmccrock
Senior Member
 
Join Date: April 23, 2007
Location: Red Rock. TX
Posts: 799
I have Warne QR rings on a couple scopes for a competition AR, one 1" and one 30mm. They go back on without having to re-zero, but I check anyway, just to be sure. Cabela's has them at $59 but I do not remember them being that much, so shop around.

The height depends on the scope bell size and the mount on the AR. Going straight onto the flat top receiver, you probably need high rings. Tricky part is getting the scope far enough forward. Usually that would mean some extension like LaRue but that is way over your budget.

Lee
lmccrock is offline  
Old December 2, 2009, 05:48 AM   #3
Desertguns
Member
 
Join Date: August 21, 2009
Location: ARIZONA
Posts: 38
Tree-
I have a Mark AR 4-12X40 on my flattop, in an American Defense AD Recon S-mount 1", but that mount is about $150 now. Try midwayusa.com, run AR-15 flattop search for mounts, and you'll come up with about 5 pages of options. If you want a qr mount made of aluminum, I saw some starting around $60 (ProMag, Model 1) but if you want steel (and I prefer throw-levers as opposed to thumb-nuts or the like), then American Defense ($150+), Larue (170+) and GG&G Accucam (200+) are solid performers. Wilson Combat makes a "Lo-Mount" in steel with thumb-nuts, and they sell for $80 or so. Had one of those for a few years, until I found the AD Recon-S. It has a medium height, plenty of eye relief, and a good repeatable-zero. Just my opinion, but I'd stay away from those 20 and 30 dollar mounts, you get what you pay for...
Desertguns is offline  
Old December 2, 2009, 12:09 PM   #4
sholling
Senior Member
 
Join Date: May 18, 1999
Location: Hemet (middle of nowhere) California
Posts: 4,258
I normally recommend biting the bullet and spending $200 for a LaRue mount, however if you can't swing the best then look at Burris' AR-P.E.P.R.. What you lose going to the cheaper mount is 1 MOA repeatability when removing and reinstalling it on your rifle.
__________________
Proud Life Member: National Rifle Association, California Rifle & Pistol Association, and the Second Amendment Foundation.
Annual Member: Revolutionary War Veterans Association (Project Appleseed) and the Madison Society.
sholling is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:13 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06244 seconds with 9 queries