The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old April 20, 2009, 03:20 PM   #1
Doyle
Senior Member
 
Join Date: June 20, 2007
Location: Starkville, MS (new to MS)
Posts: 4,663
Anybody successfully touched up a Rem bowling pin finish?

I just picked up a Rem model 7 with a couple of small bare spots on the finish. I'd rather not refinish the whole stock if I can do a successful patch job. I'm pretty sure that Remington used a 2part epoxy in the factory. I'm wondering if a gloss polyurethane applied as a touchup would be noticable.
Doyle is offline  
Old April 20, 2009, 05:46 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,405
It's not 2-part epoxy, it is a polyurethane finish that is sprayed on. You can match it pretty close with Acra-Stock Gloss from Brownells.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old April 21, 2009, 02:04 AM   #3
sadsack
Senior Member
 
Join Date: February 4, 2006
Posts: 206
I've had good results using super glue on small scratchs. It wouldn't work in this situation though.
sadsack is offline  
Old April 23, 2009, 10:06 AM   #4
Horseman
Senior Member
 
Join Date: February 1, 2006
Location: Midwest
Posts: 1,065
Remington finish

Remington's "bowling pin" finish is not polyurethane. It's a 2 part urethane clear coat. In the 80's and 90's it used to be DuPont IMRON line(and maybe still is). IMRON was and is still used to paint tractor trailers and heavy equipment. I have an early 90's Remington catalogue that actually mentions the IMRON by name. Technically it is an epoxy because it has s hardener added to the paint like any other automotive clear. IMRON is extremely durable and can be touched up with automotive clear from your auto parts store. Spray can or the little fingernail polish type touch up bottles of clear coat will match pretty well but this only works for scratches or small areas. If you have areas with no finish I'd guess the rest of the finish is not pristine. I'd respray the whole thing with automotive clear so it all matches.

If Remington isn't using IMRON anymore I'm sure they're still using a similar 2part automotive grade finish. The finish on these is still extremely hard. Polyurethane contains no hardner and relies on oils air drying to harden.
Horseman is offline  
Old April 24, 2009, 10:44 PM   #5
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
I have used a product calle Fuller Plast, it is made by the Fuller O'brien company. It is a 2 part catalyzed varnish that I understand Weatherby used, at least at one time.
I would try some automotive shops for a 2 part finish. Fuller Plast only comes in a Gallon size and way more than you need. You might also check out a WELL stocked paint store for a 2 part finish.
The nice thing about MOST 2 part finishes is that you can mix some up and make a repair (1st coat) and put the finsh in the freezer and it will stay usable quite a long time.
Ruger4570 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:26 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06504 seconds with 9 queries