The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old April 20, 2009, 03:50 AM   #1
skeeter
Senior Member
 
Join Date: October 29, 1999
Posts: 883
Any tool needed to change out M1A extractor?

i heard the only weak link on the Springfield Armory M1A's are the extractors . I bought a USGI extractor and want to know how and what is needed to change it out. Thanks
skeeter is offline  
Old April 20, 2009, 04:09 AM   #2
B. Lahey
Senior Member
 
Join Date: March 17, 2008
Location: Indiana
Posts: 2,829
I sure wouldn't try it without one. Fulton has them on their webpage. Do you have a copy of Walt's book?

Watch the compressed ejector spring, it can kill you, apparently. Strong safety glasses and watch where you point it.
__________________
"A human being is primarily a bag for putting food into; the other functions and faculties may be more godlike, but in point of time they come afterwards."
-George Orwell
B. Lahey is offline  
Old April 20, 2009, 06:22 AM   #3
wjkuleck
Senior Member
 
Join Date: March 13, 2007
Location: Ohio, USA
Posts: 1,220
Mr. Lahey refers, of course, to the bolt assembly/disassembly tool. Well worth the money, particularly because you should periodically detail strip the bolt to clean out the firing pin channel & etc., so you'll get more than the one-time use out of it.

The book is pretty good, even if I do say so myself .

Best regards,

Walt
PS ...and thanks to Mr. Lahey for the kind recommendation!
__________________
Author, NEW! The M1911 Complete Owner's Guide
The M14
and M1 Garand Complete Assembly Guides
The M1 Garand Complete Assembly Guide
The AR-15 Complete Assembly
and (New 4th Edition) Owner's Guides
wjkuleck is offline  
Old April 20, 2009, 12:00 PM   #4
nbkky71
Senior Member
 
Join Date: September 13, 2005
Location: Davidson, NC
Posts: 416
The bolt tool is quite handy and worth the money, but in a pinch you can swap extractors by using a fired .30-06 case.
  • Remove the magazine & lock the bolt to the rear
  • chamber the fired .30-06 case... it will stick out the breech.
  • Slowly close the bolt onto the fired base.
  • Push the op rod forward, compressing the ejector
  • While keeping forward pressure on the op-rod, drive the extractor out of the bolt through the magazine well.
  • While keeping forward pressure on the op-rod, replace the extractor.
It takes a little dexterity but it's a great trick to know for field-expedient repairs. I had to do this at a rifle match once when my bolt disassembled during a rapid fire string.
nbkky71 is offline  
Old April 20, 2009, 01:30 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 18,637
The handle of the M10 cleaning rod (the jointed rod for the M1 rifle) can also be used as a bolt disassembly tool the same way. Put it in the chamber, screwdriver end forward (no it doesn't touch the inside of the chamber), then close the bolt on it the same way. The handle of the M14 tool can also be used but the bolt has to be out of the rifle.

Jim
__________________
Jim K
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 12:12 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07715 seconds with 9 queries