The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old September 26, 2008, 01:39 PM   #1
Buzzard Bait
Senior Member
 
Join Date: June 25, 2008
Location: Republic of Texas
Posts: 338
oily wood how to clean

I recently acquired an old pistol that metal wise is almost mint but the wood grips are very dark with oil or handling or who knows what. My question is what method do you use to degrease the wood and make it look better?

Buzzard Bait
Buzzard Bait is offline  
Old September 26, 2008, 02:01 PM   #2
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,484
In order of increasing harshness:
* Murphy's Oil Soap and a brush
* Scott's Liquid Gold on ScotchBrite
* Dawn dish soap with Arm & Hammer Laundry Soda in hot water
* Citristrip Paint & Stain Stripper finish remover
* EZ-Off oven cleaner

After the first two, no refinishing needed. After the others, you will have to refinish the grips.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Old September 26, 2008, 03:24 PM   #3
brickeyee
Senior Member
 
Join Date: December 29, 2004
Posts: 3,342
Try paint thinner before anything else.
It will not damage any finish but removes grime and grease very well.

Do not use anything water based.
Grips are thin and can easily absorb enough water to swell, warp, and be damaged.
brickeyee is offline  
Old September 26, 2008, 05:43 PM   #4
Loader9
Senior Member
 
Join Date: July 29, 2008
Posts: 949
WD-40 is your friend for cleaning old dark wood.
Loader9 is offline  
Old September 26, 2008, 08:10 PM   #5
hockeysew
Member
 
Join Date: August 21, 2008
Posts: 91
Sometimes the old ways are the best ways.
Give this a try:
Round up some "Whiting" Basically ground chalk- a pottery supply store will have it and it is cheap-.75 cents a pound! Get a couple of pounds.
Pick up some Denatured Alcohol.
Mix the Whiting into some of the Alcohol and make up a paste about like toothpaste.
Slather it on to a warm stock with a 1" paint brush.
Let the paste dry and brush off the powder.
If the stock is really oily it will help to dampen it with mineral spirits first.
Repeat as needed. This will leech out the majority of the oil without harming the stock.
Harsh chemicals can damage the wood and cause reactions with stains and or change the color of the wood.
hockeysew is offline  
Old September 27, 2008, 05:14 PM   #6
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,349
I did a whole Garand stock that way once. Slow but effective. Note the tip on warming the wood. After the alcohol had evaporated (that's important) but while the dust was still holding its coating shape on the wood, I actually put mine into a low oven at about 150° to drive more of the oil up into the chalk.

Agricultural lime works, too. It is also calcium carbonate (chalk), though it isn't always quite as fine. Very cheap. The most effective is fumed silica dust, because it has the most surface area, but it isn't as cheap. Unless you can get it at work, don't bother.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Benefactor Member
Unclenick is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06306 seconds with 9 queries