The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 2, 2008, 10:06 PM   #1
DaveInPA
Senior Member
 
Join Date: January 20, 2008
Location: Berks County, PA
Posts: 1,106
Your favorite .45ACP 200gr LSWC loads?

I have 2,000 200gr LSWC bullets on my bench waiting to get loaded up. I have the following powders on hand: W231, Titegroup, WSF, AA#5, and AA#7.

Anyone care to share any favorite loads for any of these powders?

Thanks!
Dave
DaveInPA is offline  
Old May 2, 2008, 10:15 PM   #2
nobody_special
Senior Member
 
Join Date: November 20, 2006
Location: Southwest US
Posts: 277
I use HP38 (identical to W231) with 200 gr. RNFP. I suggest around 4.8 to 5.0 gr of W231 for a plinking round... this isn't at max pressure but it works nicely.
nobody_special is offline  
Old May 2, 2008, 11:38 PM   #3
hivel37
Senior Member
 
Join Date: August 24, 2004
Location: Hill Country
Posts: 521
Haven't used any of the powders you have listed.

Have used 4 grs of 700X and 6 grs of Universal.

Amazing the price jump those 200's have taken over the past year.
hivel37 is offline  
Old May 2, 2008, 11:52 PM   #4
cheezhed
Senior Member
 
Join Date: November 28, 2007
Posts: 287
I use 5.0 grains of 231
cheezhed is offline  
Old May 3, 2008, 01:05 AM   #5
TexasSeaRay
Senior Member
 
Join Date: November 19, 2007
Location: Texas
Posts: 810
5.0 of 231 always works pretty good for me.



Jeff
__________________
If every single gun owner belonged to the NRA as well as their respective state rifle/gun association, we wouldn't be in the mess we're in today.

So to those of you who are members of neither, thanks for nothing.
TexasSeaRay is offline  
Old May 3, 2008, 01:25 AM   #6
DaveInPA
Senior Member
 
Join Date: January 20, 2008
Location: Berks County, PA
Posts: 1,106
What's your OAL and crimp on that 5.0gr 231 load?
DaveInPA is offline  
Old May 3, 2008, 09:40 AM   #7
jhansman
Senior Member
 
Join Date: June 17, 2007
Posts: 624
5.4 gr. of Titegroup always worked nicely for me with that bullet and a WLP primer. It's an excellent powder for reasons that have been discussed here many times.
__________________
Blessed is the man who has nothing to say, and cannot be compelled to say it.
jhansman is offline  
Old May 4, 2008, 09:55 AM   #8
ShootingNut
Senior Member
 
Join Date: December 27, 2006
Location: Wisconsin
Posts: 1,470
Acc#5 pushes my 200 gr RNFP with a 8.0 to 8.2 charge, seems to work out very well for my gun.
ShootingNut is offline  
Old May 6, 2008, 09:11 PM   #9
zebulonsmith
Senior Member
 
Join Date: October 27, 2007
Posts: 307
My target load for anything less than 50' is 7.5 gr of #5 does very well out of my Springfield 1911. Pretty low velocity, but I don't see any drop at that range.
zebulonsmith is offline  
Old May 7, 2008, 01:47 PM   #10
drail
Junior member
 
Join Date: February 2, 2008
Posts: 3,150
4.3 gr. Winchester Super Target or Bullseye. The long discontinued Winchester/Olin 452AA was the best powder I ever found for 200 gr SWC. One hole groups out of my Springfields and my S&W 625. Super Target is almost as good.
drail is offline  
Old May 7, 2008, 06:30 PM   #11
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 8,936
drail, how about a .45 load with 200 grain LSWC and the discontinued Win 473AA powder? I've got a few cans of it and I'd love to roll .45 with it. I've heard it works for .45, but without data, I'm not big on experimenting.

For the original poster, my 200 grain LSWC is 4.4 grains of Bullseye, but that wasn't list as one of your powders.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old May 7, 2008, 06:56 PM   #12
Striker1
Senior Member
 
Join Date: May 22, 2004
Location: TX
Posts: 635
5.1 gr W231 and Lasercast 200 gr SWC works good in both my Gov't Models.
Striker1 is offline  
Old May 7, 2008, 07:32 PM   #13
Sarge
Senior Member
 
Join Date: May 12, 2002
Location: MO
Posts: 4,911
The following are good with any quality H&G #68 or close copy. 1.250" OAL, W231 powder, Winchester primers and a good snug taper crimp to prevent bullet setback.

4.0 grains, for 626 fps
. Cycles & feeds perfectly in my USGI pattern 1911, really thumps pests/small game load & shoots to the sights at 20 yards or a tad further. Quiet enough that a few rounds w/o earplugs will not deafen you. Will just shoot through a pine 2x4 and sink the nose in another behind it. A friend pointed out that the ballistics of this load is a near match for the old .38, 200 grain Super Police load and I would not hesitate to use it for indoor defense. I use this load to 'cycle-out' worn-out casings and stain them black to make them readily identifiable. A favorite 'fun load' and perfect for introducing small folks to the 1911.

Same as above except 5.0 grains, for 826 fps. Good accurate load with negligible recoil, groups right along with decent JHP's like WW/USA 230; shoots to the same POI out to 50 yards. Would serve fine as a defense load if that what happens to be in the gun. I wouldn't hesitate to heart-shoot a deer with it either. Another favorite.

Yes, W231 is the official "zero to sixty" pistol powder around here. As noted above, HP38 is essentially a direct replacement.
__________________
I'm inclined to think if a man hasn't gotten his point across in 4912 attempts, 4913 probably isn't going to do it.
Sarge is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09136 seconds with 9 queries