The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 10, 2008, 06:05 PM   #1
Ghost22
Member
 
Join Date: January 19, 2006
Posts: 64
Lee Hand Press for Beginners

I'm thinking of getting into metallic reload but am low on funds with an upcoming wedding and fresh-out-of-college bills. The Lee Hand Press seems to fit the bill, as it would take up very little space in my apartment and many people seem to keep it around for loading handfuls of trial rounds. As for my background, I’ve reloaded around 1000 rounds of shotgun ammunition a year during highschool and read my dad’s reloading manuals/magazines whenever I get the chance. (He used to reload an array of rounds but now only reloads the occasional “deer season” batch and said shotgun shells.) I’m looking to reload around 100-200 round in .38 special and .357 magnum after I get the hang of it.

Thanks for the thoughts.
Ghost22 is offline  
Old April 10, 2008, 06:17 PM   #2
SavageMOA
Senior Member
 
Join Date: March 19, 2008
Posts: 368
I've never personally used the Lee hand press but I've heard that several people like theirs, especially for apartments. There are definately better and faster presses around but that's definately the cheapest. It all depends on how much you plan on loading at a time.
SavageMOA is offline  
Old April 10, 2008, 06:19 PM   #3
JJE
Member
 
Join Date: November 1, 2006
Location: Oakland, CA, USA!
Posts: 71
I have an RCBS turret press and powder dispenser mounted on the corner of my wife's sewing table. It takes up hardly any room. What takes up a lot more room is the boxes of dies, powder, empty ammo boxes, full ammo boxes and all the other stuff that you need to get whether you get a hand press or a standard press. I can see using a hand press if you want to be able to load at the range as you develop a load. Otherwise, I would just get a standard press, even if I had to save up for it.
__________________
Julian

California Rifle & Pistol Association and NRA Life Member
JJE is offline  
Old April 10, 2008, 10:03 PM   #4
amamnn
Senior Member
 
Join Date: May 13, 2006
Location: WA, the left armpit of the USA
Posts: 1,323
I used a 9mm Lee hand press for a while it was ok for making plinking rounds. I'd guess that the .357 version would too.
__________________
"If the enemy is in range, so are you." - Infantry Journal
amamnn is offline  
Old April 10, 2008, 10:21 PM   #5
Sevens
Senior Member
 
Join Date: July 28, 2007
Location: Central Ohio
Posts: 8,291
Were I in your shoes, I would skip the hand press and instead, buy the cheapest mountable press you can find. Lee makes a very cheap one and though it'll likely flex more than you'd like for some heavy rifle cartridge resizing, I don't see it being any kind of trouble (durability wise) for .38/.357. You might even consider moving to their o-frame press, the Lee Breech-lock Challenger, which will also do a fine job even on large rifle rounds if you ever move toward them.

The physical space that it takes up is not a reason to avoid it-- you'll have much better leverage for working your cases, and when it comes to re-sizing, it's all about leverage. It needn't be a permanent mount, many folks have had fine luck mounting the press to a short plank of sturdy wood, and then temporarily c-clamp that plank to a place to work, even if it's the kitchen table.

This press will be a tool that you will still comfortably use 5 or more years from now when you hopefully have more space and money to go further in your reloading.
__________________
Attention Brass rats and other reloaders: I really need .327 Federal Magnum brass, no lot size too small. Tell me what caliber you need and I'll see what I have to swap. PM me and we'll discuss.
Sevens is offline  
Old April 11, 2008, 02:42 AM   #6
moose fat
Senior Member
 
Join Date: June 20, 2006
Location: Alaska, Yukon R. delta
Posts: 383
I like mine. I don't reload all that much maybe 500 rnds./yr in three rifle calibers. Everything fits in two cardboard boxes.

I can make custom ammo, its a good tool.
moose fat is offline  
Old April 11, 2008, 03:55 AM   #7
Sgt.Dusk
Member
 
Join Date: December 12, 2007
Location: The dark forests of scandinavia
Posts: 32
Lee handpress is good. For a sofa/TV reloader like me it works better than
a benchpress. There is no trouble resizing rifle brass, you just gotta lube
cases good.
I load about 500 .357's and 100 7.62X54R / month.
Maybe if I had to reload more Id buy a turret/progressive press but for now its enough.
Sgt.Dusk is offline  
Old April 11, 2008, 10:34 AM   #8
freakshow10mm
Junior member
 
Join Date: January 23, 2008
Location: MI
Posts: 1,398
I started on a Lee hand press for 10mm. Thankfully I upgraded with a present from my mother. The hand press is good for loading at the range or doing chores like decapping military brass in front of the TV, etc.
freakshow10mm is offline  
Old April 11, 2008, 03:22 PM   #9
shepherddogs
Senior Member
 
Join Date: January 9, 2007
Posts: 1,007
Get a real press, you won't regret it. Even if you later move up to expensive progressive equipment you will always find a use for a single stage.
shepherddogs is offline  
Old April 11, 2008, 03:35 PM   #10
dwhite
Senior Member
 
Join Date: September 2, 2007
Location: Wake County, N. Carolina
Posts: 279
Lee hand press

I bought one of these about a year ago for the same reasons, limited funds and space. I use it to load .38/.357 and 40S&W. Overall it's a good unit. I like the fact it fits in a small box under the bed. Easy to set-up and operate. I wouldn't want to try full length sizing a lot of.30-06 cases on it but for what I do it's great. I load about 300 rounds per month. Fifty rounds get completed in about an hour.

Go for it. You'll like it.

All the Best,
D. White
Wake County , NC
dwhite is offline  
Old April 12, 2008, 03:59 PM   #11
twhidd
Senior Member
 
Join Date: March 21, 2005
Location: Athens, Georgia
Posts: 788
I have a Lee hand press. With that, a set of dies, and a set of of the Lee powder dippers, I have all that I need to do some "basic" reloading. I reload 38 and 357 with it. I can do about 50 or so rounds an hour.
twhidd is offline  
Old April 15, 2008, 02:01 AM   #12
ConfuseUs
Senior Member
 
Join Date: April 26, 2007
Posts: 461
I like mine since I break up the reloading process into prepping a batch of brass, priming a batch of brass, and then loading rounds at my leisure since charging the cases takes the most time. The hand press is really good for doing things like decapping brass or sizing brass while watching TV. It is also compact enough that I can store all my reloading tools in a large surplus ammo can and don't need to have a dedicated reloading bench.

I've loaded 9mm and .223 on mine, and the final parts of the loading process are somewhat less convenient with the hand press as compared to loading on a friend's bench mounted press.
__________________
Overkill is better than underkill.
ConfuseUs is offline  
Old April 16, 2008, 01:58 AM   #13
Hook686
Senior Member
 
Join Date: May 22, 2005
Location: USA The Great State of California
Posts: 1,858
I used a Lee Hand Press before I got the Lee Turret. I used Lee Carbide dies with it, for .357 magnum, .44 magnum and 9mm. I use the Lee perfect powder measure and an RCBS scale and a Lyman hand primer.

I typically produced about 50 rounds per hour in batches of 100. I'd clean, resize/deprime, prime 100 cases ... then add powder and seat bullet for the 100, one at a time. I found it tough to screw up with all the 100 cases prepared and then adding powder and seating a bullet one at a time. I never had a double charge, or a squib with the Lee Hand Press.

I use the Lee Turret now, but keep the Hand Press for the occasional trip to the range.
__________________
Hook686

When the number of people in institutions reaches 51%, we change sides.
Hook686 is offline  
Old April 16, 2008, 03:22 AM   #14
Sport45
Senior Member
 
Join Date: May 25, 1999
Location: Too close to Houston
Posts: 4,017
Welcome to The Firing Line!

I've never used or for that matter even seen a hand press, but it sounds like a good choice if space is the issue. If the constraint is only budget keep an eye on ebay for Lee or Lyman presses. Sometimes you can find a pretty good deal. Like this one.
__________________
Proud member of the NRA and Texas State Rifle Association. Registered and active voter.
Sport45 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:36 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.10607 seconds with 9 queries