The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 7, 2007, 06:15 PM   #1
lemmonhead
Member
 
Join Date: June 14, 2004
Posts: 21
Pulled bullets?

A little history first. I have been reloading for my brother in law's .280. I worked up a good load using H4831 with Hornady 139 gr SST bullets. He bought a box of Barnes triple shock bullets of the same weight and wanted me to reload a couple of boxes for hunting season using the same load data. I did not have the rifle and told him I cannot guarantee accuracy. Well needless to say accuracy is awful.

So the question is if I pull the bullets with a kinetic bullet puller can I expect to get decent accuracy out of the bullets? These are expensive bullets and I would like to make the shoot decent. I have the rifle this time and plan on working up a load.
lemmonhead is offline  
Old December 7, 2007, 06:46 PM   #2
BigJimP
Senior Member
 
Join Date: February 23, 2005
Posts: 11,228
unless there is some significant scarring on the neck of the bullets after you pull them - I'd reuse them. I routinely re-use bullets that I have to pull / or bullets from test loads that didn't work out.

If you have some uncertainty about the bullets - load them up in cases and mark the bases of the case with a marker pen - and just shoot them up for practice.
BigJimP is offline  
Old December 7, 2007, 08:13 PM   #3
Thesenator
Senior Member
 
Join Date: April 12, 2006
Posts: 120
Bullets pulled with kinetic pullers(especially hand done ones) are usually very reloadable, its bullets done on high volume machines that deform the bullets which might have accuracy issues. These bullets usually have "pull marks"(a split line running parallel to the bullet's axis) and are more often than not a little out of round unless run through a resizer and brought back into round.
I shoot alot of pulled bullets for plinking ammo at 100yds and they work just fine for that, for longer ranges or more precision shooting I use new bullets.

If you are using lead tipped hunting bullets and the tip is deformed badly, as posted above, use them for practice.
Thesenator is offline  
Old December 8, 2007, 10:18 AM   #4
lemmonhead
Member
 
Join Date: June 14, 2004
Posts: 21
Thanks for the responses. Since they are Barnes bullets and a little expensive I will reload them. I do not have much experience with Barnes bullets but I’m a little surprised at how bad they shot with a load that should have been a little functional. Lesson learned though. If I can get them down to 1" to 1 1/2" at 100 yards that will probably be good enough for him.
lemmonhead is offline  
Old December 8, 2007, 11:56 AM   #5
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,018
Every so often I have to pull match bullets. I use a kinetic bullet puller when possible. I will shoot the stuff again, will shoot perfect, or pretty close to perfect scores in the rapids out to 300 yards.

But at 600 yards, in the back of my head I am thinking, "is that a used bullet", so I use NIB bullets at that yard line. I really doubt there is any on target difference, but you have to calm your fears...
Slamfire is offline  
Old December 8, 2007, 12:27 PM   #6
snuffy
Senior Member
 
Join Date: May 20, 2001
Location: Oshkosh wi.
Posts: 2,758
TIP. Put a foam earplug in the bottom of that kinetic puller, to avoid damaging the tip of the bullet. Works for the lead tipped as well.

Most guns can't tell the difference between pulled bullets and NIB ones.
__________________
The more people I meet, the more I love my dog

They're going to get their butts kicked over there this election. How come people can't spell and use words correctly?
snuffy is offline  
Old December 8, 2007, 01:28 PM   #7
RDub
Member
 
Join Date: November 13, 2007
Location: Southern Oregon
Posts: 30
Most guns can't tell the difference between pulled bullets and NIB ones.

Exactly right!

However.. You can damage bullets if they come out too hard.. So, a little technique is required when pulling bullets with a kinetic puller. Most experienced reloaders already know this, but in case someone is just getting started...

As you see the bullet start working its way out of the case with consecutive strikes on the ground.. lighten up on the pounding and start 'tapping' until the bullet actually just 'falls' out.. like you just let it go with your fingers. Experience will give you the 'feel' for this.
And like snuffy said, putting something in the bottom of the well is very helpful. I use a little cotton ball shoved down, but not compacted too much.

Yep, Barnes bullets seem to require some messin with to find a accurate load in a lot of cases.. So dont feel bad.
Barnes does say, that their bullets should be seated .050" from the lands, and that is a pressure related recommendation and not necessarily providing the best accuracy..
RDub is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:30 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07158 seconds with 9 queries