The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 18, 2006, 08:01 PM   #1
gearyr
Junior Member
 
Join Date: July 12, 2004
Location: Castalian Springs, TN
Posts: 8
Any Pet loads for 8mm Mauser?

I have been trying to get a great load for my scoped Yugo M48. I have Sierra 175 grain SP. I have loaded up 30 rounds using 49.4 grains of H4895, col at 3.100. I have some IMR4064 and IMR4320. Any body have a great load using IMR4064 & IMR4320 with the Sierra 175 grain bullets? I also need the col. Thanks, gearyr.
gearyr is offline  
Old November 12, 2007, 08:02 PM   #2
scott6509
Junior Member
 
Join Date: November 12, 2007
Posts: 2
I have a Yugo Mauser and found a pretty good load that gives 1-1.5 MOA groups. The other day I put four bullets through two holes at 50 yrds and got a 2.5 in. group at 200 yds running a cheap Swift 9x scope. BTW, I'm not any kind of an expert shot.

Anyway, here it is:

Sierra 175 gr. with 46 gr. of 4064 and Fed 210 primer. Don't seat the bullet deep. Set it as far out as is reasonable. I don't know if that had much to do with anything, but I thought I'd mention it. I haven't chronographed it myself, but the Sierra book says this bullet should fly about 2400 fps. I have found Sierra's numbers are pretty close when using their bullets.

Good luck,
B
scott6509 is offline  
Old November 12, 2007, 08:14 PM   #3
oldscot3
Senior Member
 
Join Date: July 1, 2007
Location: texas
Posts: 301
I've used the same 175 Sierras with imr4064 also. Shot right to the point of aim with my open sighted Persian mauser with good accuracy. I recall a little better velocity but my weapon has a 29" barrel.
oldscot3 is offline  
Old November 12, 2007, 08:36 PM   #4
scott6509
Junior Member
 
Join Date: November 12, 2007
Posts: 2
I'll mention a load that didn't work:

150 gr Sierra with 49.6 gr. of 4064 and Fed 210 primers. These shot all over the place. Maybe 4 MOA. One shot went high, the next low, the next right or left. Couldn't get any consistancy at all. Goes to show how much different loads can make.
scott6509 is offline  
Old November 13, 2007, 07:39 AM   #5
DavidJBlythe
Senior Member
 
Join Date: December 1, 2005
Location: USMC, Centcom
Posts: 214
I had good experience with Hornady round nose bullets (170 gr I think) over 38 gr of IMR 4895. This is an underpowered load, but was pretty accurate.

Currently my fav load is:
150 Gr. Hornady SP Interlock #3232
40.0 Gr. Varget
CCI #200 Large Rifle Primer

This is a med-high strength load with good accuracy.

I have tried full power loads pushing a 220 gr Hornady round, but my shoulder couldn't take it.
DavidJBlythe is offline  
Old November 13, 2007, 01:48 PM   #6
Scorch
Senior Member
 
Join Date: February 13, 2006
Location: Washington state
Posts: 11,408
I went back and checked my notes from 1987. 175gr Sierra, 49.2 gr IMR4320, WW LR primer. About 1 1/2" at 100 yds.
__________________
Never try to educate someone who resists knowledge at all costs.
But what do I know?
Summit Arms Services
Taylor Machine
Scorch is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07801 seconds with 9 queries