The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 1, 2007, 10:33 PM   #1
20nickels
Senior Member
 
Join Date: July 2, 2007
Posts: 274
Loading white hot .38's

I don't want to get into why I would not just use .357 brass, here is the question;
Is there any reason (other than slight length difference) you couldn't load a .38 case to .357 magnum levels in a strong, properly supported chamber such as a Ruger GP100?
Is the .357 case stronger around the primer pocket area? Anybody have crossection pics? Tks, ahead. Nickels
20nickels is offline  
Old November 1, 2007, 10:51 PM   #2
joneb
Senior Member
 
Join Date: December 10, 2005
Location: Central , OR
Posts: 1,729
.357 mag cases are built stronger to handle x2 the pressure, the greatest danger in doing this is that these rounds may fall into unsuspecting .38 spl chambers
joneb is offline  
Old November 1, 2007, 11:29 PM   #3
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
Also if you shoot enough of the hot 38's you could turn you 357 into a 38. I can't say it will happen to a Ruger but I do have a friend, not a friend of a friend, who did this and after awhile and even after a good cleaning could not get a 357 to extract without extreme difficulty.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old November 2, 2007, 01:03 AM   #4
Crosshair
Senior Member
 
Join Date: December 16, 2004
Location: Grand Forks, ND
Posts: 5,320
You will have to do a good job of cleaning to get rid of the fouling should you wish to fire 357 out of it. Other than that, the only real reason is that you will have case head separations happen after a few loadings. Some cases last awhile, some will separate ofter a loading or two. Keep a small flathead screwdriver handy to poke those cases out from the front of the cylinder.

Also, mark the case heads with a red sharpie to designate them as high pressure loads.
__________________
I don't carry a gun to go looking for trouble, I carry a gun in case trouble finds me.
Crosshair is offline  
Old November 2, 2007, 01:21 AM   #5
BillCA
Senior Member
 
Join Date: November 28, 2004
Location: Silicon Valley, Ca
Posts: 7,087
Sure, you can load a .38 to .357 Magnum levels, but the question is why.

The first prototypes were hot-rodded .38 Special cartridges fired in the .38/44 Heavy Duty (ancestor the model 27/28). Since the advent of the .357 Ctg the loads have been well researched and designed for the longer case.

The first obvious problem is inadvertently slipping one of these hot loads into a .38 Special chamber. The .38 Special chambered guns are not heat treated to withstand the extra 13,000 to 15,000 psi of a Magnum load. The result may look (and act!) like a grenade.

Secondly, you risk cartridge-case failure when firing. It's possible to have excessive pressures in such a handload that cause case heads to rupture or a primer to crater or flow, releasing hot gasses from the primer pocket and tying up the action. The case may split in the chamber as well.

Third, the longer jump from the .38 case to the forcing cone may cause throat erosion and/or cracking, flame cutting of the top strap, erosion of the cylinder face or barrel mouth. The longer jump from the shorter .38 case may also reduce accuracy.

Lastly, I don't think you'd gain anything. You'd still need to fire such a load in a .357 chambered gun. Accuracy may be less than using a .357 case and you'll be fouling the chamber mouths excessively most likely.

Remember the old axiom:
Just because you can do something, doesn't mean you should do something.
__________________
BillCA in CA (Unfortunately)
BillCA is offline  
Old November 2, 2007, 09:33 AM   #6
20nickels
Senior Member
 
Join Date: July 2, 2007
Posts: 274
So the case itself is different.

The firearm I'm referring to is a .357 customized to chamber .38's only and the barrel set back (I know it's weird but it's not mine), and yes, it is plenty strong for .357.

Tks for the reply's.
20nickels is offline  
Old November 2, 2007, 10:49 AM   #7
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 10,926
The October 2006 Handloader magazine had an article on the .38-44 Heavy Duty and a tabulation of loads at or above the old H.D. A 158 at 1200 OK?
http://www.riflemagazine.com/magazin....cfm?magid=141

As to brass, Skeeter Skelton said he started with once fired .38 special and only loaded it so heavily one or a very few times.
Jim Watson is online now  
Old November 7, 2007, 09:07 PM   #8
Shell Shucker
Member
 
Join Date: September 27, 2007
Posts: 46
Pressure will be HIGHER in 38SPL cases than 357 cases if the OAL is not the same. Risky business! You may not blow up YOUR gun. Your loads may inadvertently blow up somebodies gun if they find a home in a weak chamber..........
Shell Shucker is offline  
Old November 7, 2007, 09:14 PM   #9
Capt Charlie
Staff
 
Join Date: March 24, 2005
Location: Steubenville, OH
Posts: 4,304
I think this is appropriate for this thread. Just a friendly caution, so no one ends up with a very big ouchie .
__________________
TFL Members are ambassadors to the world for firearm owners. What kind of ambassador does your post make you?

I train in earnest, to do the things that I pray in earnest, I'll never have to do.

--Capt. Charlie
Capt Charlie is offline  
Old November 8, 2007, 04:43 AM   #10
Unclenick
Staff
 
Join Date: March 4, 2005
Location: Ohio
Posts: 10,195
20 Nickels,

The .357 case was made longer so it couldn't be chambered in a .38 special revolver. Same deal as the .44 Magnum, which Elmer Keith developed by loading up .44 specials in a large frame revolver. In the commercial version, they just didn't want accidental cross-chambering.

There is no reason a .38 Special +P+ case would not hold up to .357 pressures. Because it is shorter, it will reach those pressures with less powder if you are not able to seat the bullet out to SAMMI .357 maximum COL, which is 0.04" longer than .38 Special maximum COL. In the case of H110/W296, that 0.04" deeper seating of the bullet will raise pressure about 10%. With a 158 grain bullet, knocking a .357 load of this powder down about 1/2 a grain will compensate for the pressure increase.

Are you sure the adapted cylinder has proper heat treatment? I assume the cylinder is custom made in order to be reamed for .38 Special throat length? That's no guarantee it got same heat treatment as a factory .357 cylinder gets, but it may have. None of them is heat treated very hard, as they can all be reamed later during accurizing, but it isn't zero heat treating in most cases, either.

Tim R,

Your friend's cylinder still has lead caked in it. Have him remove the cylinder and soak the whole thing in Kroil for a week, then go after it with an undersize brush that has had several strands of Chore Boy 100% copper cleaning pad wrapped around it. That or a Lewis Lead Remover. The lead should come right out. If that somehow fails, he should get the use of an Outer's FoulOut, and use the lead solution to get the rest. He'd have to plug the business end of each throat and go at them one-at-a-time. Not a lot of excitement in that possiblity.
__________________
Gunsite Orange Hat Family Member
CMP Certified GSM Master Instructor
NRA Certified Rifle Instructor
NRA Patron Member
Unclenick is offline  
Old November 11, 2007, 07:13 AM   #11
IDLH1950
Member
 
Join Date: July 3, 2006
Location: Pine Bluff, Ar.
Posts: 67
I don't think that a .357 mag case is any stronger than a .38 special case. The .357 case is made slightly longer to prevent accidental loading of a .357 mag round into a .38 special revolver.

If you decide to do it, you must be aware that if someone who doesn't know that the .38 special case is actually a .357 mag round, could really have a bad day.

dave
IDLH1950 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:09 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09401 seconds with 9 queries