The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 20, 2007, 06:59 PM   #1
45reloader
Senior Member
 
Join Date: May 20, 2006
Location: PA
Posts: 669
Smoke free 45 Colt powder?

I'm not sure if it's just me being picky but I seem to remember my last reloads smoking less then this last batch.

Maybe it's me.

But before I buy anymore powder what powder do you use?
45reloader is offline  
Old June 20, 2007, 07:06 PM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,075
What bullets? Most of the smoke is from smoldering cast bullet lube.
Jim Watson is offline  
Old June 20, 2007, 07:37 PM   #3
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,513
I agree with Jim, most of the smoke is due to the lube on lead bullets, and lead is almost always what folks use in .45 Colt.

However since you asked about powder, I have been using Universal Clays quite a bit in my .45 Colt loads and it burns very cleanly. I still get smoke from the lube, but the cases are clean - no soot.
Mal H is offline  
Old June 21, 2007, 04:51 AM   #4
45reloader
Senior Member
 
Join Date: May 20, 2006
Location: PA
Posts: 669
I always pick up the Oregon Trail Laser-Cast Bullets at Cabela's.

Never had an issue before.

Maybe I'll order the RLN from penn bullets also.Always used them for just hard cast hunting lead bullets before.Just to save on shipping,and I use my Cabela's points to buy bullets at the store,which really keeps the price low.
45reloader is offline  
Old June 22, 2007, 10:55 AM   #5
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
For most of my 45 LC rounds I use Herco. I never noticed any freat amount of smoke from my loads, other than the few Black Powder ones.
Ruger4570 is offline  
Old June 23, 2007, 11:27 AM   #6
subierex
Member
 
Join Date: March 26, 2007
Location: SW Ohio
Posts: 36
It doesn't seem to be Titegroup. I shoot 200gr LRNFP (from Kempfs) target loads in my (Rossi) 1892 45 Colt and it smokes quite a bit from the breech. Also, the brass is badly sooted (?) on one side. I love this load though as it seems very consistent/accurate.

I plan on trying Unique for my next batch, but I'm not holding out any hope for cleaner burn.
subierex is offline  
Old June 23, 2007, 11:37 AM   #7
Linear Thinker
Senior Member
 
Join Date: February 10, 2007
Location: Blue State, NE US
Posts: 202
Win231 smokes very little in 45 Colt, but I don't use open lead bullets any longer. Experimenting with Trail Boss, very little smoke with a mild load of 5.6 grains under 250gr Rainier copper-plated heads.
LT
Linear Thinker is offline  
Old June 23, 2007, 11:59 AM   #8
Slamfire
Senior Member
 
Join Date: May 27, 2007
Posts: 4,079
I believe that most of the smoke is from bullet lubes. There may be some from powder residue, but it is not enough that I can recall any. And I have been shooting 45 LC's since 1987, shot at least 10,000 rounds with a 255 L and 8.5 grains Unique.

Smoke does not make any difference on target. So I think the emphasis on "clean" burning powders is "much ado about nothing".
Slamfire is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:51 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07301 seconds with 9 queries