The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 23, 2006, 12:44 AM   #1
ILgunman
Junior Member
 
Join Date: December 22, 2006
Location: Central Illinois
Posts: 9
Cleaning Hulls

I am looking for a way to clean shotshell hulls for reloading.

Someone brought me several (1000+) AA hulls they have picked up from a local state park were they dove hunt. They are slightly muddy, and some have the primers rusted (those I throw away) and I am looking for a way of cleaning them. I have heard of guys running them through a washing machine, but I think I would be divorced if I tried that. Not to mention the possibility of water remaining in the shell and rendering the shell a dud.

Any ideas of how to clean many shells at once?
ILgunman is offline  
Old December 24, 2006, 05:01 PM   #2
Foxman
Senior Member
 
Join Date: August 13, 2005
Posts: 466
I used to put them in a plastic 5 gal barrel with soap and water and keep giving them a good stir up. Then rinse out with a hose and lay them on some burlap to dry, gave them a final dry with a fan heater before processing them ( I used to deprime first as well). You could look round for a used wash machine if you have the room I guess and automate it some.
__________________
Better the man suspected of being a fool keep his mouth shut, than to open it and remove all doubt.
Foxman is offline  
Old December 24, 2006, 10:09 PM   #3
Ruger4570
Senior Member
 
Join Date: April 3, 2005
Location: Rochester, New York
Posts: 2,136
I reload tons of shotgun shells, most I buy, but I am not against picking up some good looking shells. I really don't fool arond with shells that are dirty or mud covered. They are just too cheap to fool around with. Go to shoots at local clubs, many sell the empties cheaply and they are in good shape.I don't have lots of money to burn, but I wil be damned if I am going to wash shells to save a couple of bucks. Do what ever you like though..
Ruger4570 is offline  
Old December 28, 2006, 11:22 AM   #4
ILgunman
Junior Member
 
Join Date: December 22, 2006
Location: Central Illinois
Posts: 9
I am not washing them, I just don't want to chance water in them.

I have a small concrete mixer that I am tumbling them in with silica sand. It cleans the dirt and powder residue off well, but I can only leave them in about 10 minutes tops. That doesn't get the brass very clean. Any longer starts to rough the plastic. After the silica I wipe them with a rag sprayed with silicone lubricant, slicks them right up.
ILgunman is offline  
Old May 2, 2007, 08:11 PM   #5
Lavid2002
Senior Member
 
Join Date: April 6, 2007
Posts: 2,568
fill up a slop sink with warm soapy water and slush around the hulls in it. empty-refil-rinse...repeat until water is clear when sloshed around
deprime after dry and let sit 1 day, water will trap itself in the flash hole ruining the new primer so let it sit a day or two to dry after depriming : D your good 2 go : P
__________________
Math>Grammar
Lavid2002 is offline  
Old May 3, 2007, 01:11 PM   #6
Shoney
Senior Member
 
Join Date: February 21, 2002
Location: Transplanted from Montana
Posts: 2,311
For about 45 years I have done the following only with hulls having a one piece formed plastic with brass base:

clean off crud by hand
wash hulls: old nylon stocking in washer when wife isn't home
dry
deprime
dry
load

Using a little common sence on drying time in the sun & wind, I have never had a problem with water in the hull.
__________________
I pledge allegiance to the Flag - - -, and to the Republic for which it stands….Our Forefathers were brilliant for giving us a Republic, not a democracy! Do you know the difference??? and WHY?http://www.wallbuilders.com/LIBissue...les.asp?id=111
Shoney is offline  
Old May 3, 2007, 02:13 PM   #7
WCW
Senior Member
 
Join Date: March 6, 2007
Posts: 131
I never wash hulls. I simply rag off any debris, check the interior for anything like feathers or whatever, and then load ‘em up. They last this way until the crimps are so burned they really don’t work so well anymore, and I simply toss ‘em. Two non-reloading dove hunting friends who pick up their empties will give you a lifetime supply of hulls for absolutely nothing. Baring that, local trap and skeet clubs sell hulls cheap. Cleaning shotgun hulls isn’t worth stirring the ire of the better half, nor needlessly mucking up a perfectly good washing machine.
WCW is offline  
Old May 4, 2007, 01:57 AM   #8
mc223
Senior Member
 
Join Date: January 20, 2007
Location: n/w Wisconsin
Posts: 365
Plastic base wads in the washer are ok, but paper base wads really get mushy.
I toss mine in a tumbler of untreated corn cobb over night, then decap and inspect, then just load em up.
mc223 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:56 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08250 seconds with 9 queries