The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 24, 2007, 11:59 PM   #1
nass
Senior Member
 
Join Date: December 28, 2006
Location: SE Michigan
Posts: 281
Lube the lever primer arm?? - Lee Classic Turret Press

Should one lube the lever prime arm on the classic turret press? I found it likes to annoyingly stick every once in a while in the "priming" position even through multiple strokes. Makes it fun if you don't catch it before depriming the next case.

Any tricks to making sure it always falls free? I shot a bit of rem-oil in there and it got a bit better.
__________________
My $0.02
nass is offline  
Old April 25, 2007, 05:36 AM   #2
CrustyFN
Senior Member
 
Join Date: June 4, 2006
Location: West Virginia
Posts: 2,258
Mine used to stick once in a while but I find the more I use it the better it works. I have never lubed it.
Rusty
__________________
I don't ever remember being absent minded.
CrustyFN is offline  
Old April 25, 2007, 05:49 AM   #3
ECLIPSE45ACP
Senior Member
 
Join Date: January 9, 2007
Location: Omaha, NE
Posts: 177
Lubing it makes it worst almost. it gunks up from the deposits coming out of the spent primers. Like said earlier the more you use it the better it gets, it could be gunked up clean it out with some gunsrubber, or similar solvent it worked for me. make sure u clea the shellholder too, sometimes that gets gunked up as well

-Dan
ECLIPSE45ACP is offline  
Old April 25, 2007, 07:36 AM   #4
zymurgest
Junior Member
 
Join Date: September 3, 2006
Location: Ohio
Posts: 14
I found that the edges on the body of the primer arm (large & small) had a little flash on them and I deburred with a stone.. never has stuck and I do not
lube other than a light coat of Rem Oil when changing them.
zymurgest is offline  
Old April 25, 2007, 07:56 AM   #5
nass
Senior Member
 
Join Date: December 28, 2006
Location: SE Michigan
Posts: 281
Thanks for the responses... I was concerned using anything for fear of the gunk buidup. A bit of the wimpy rem-oil did seem to help it from sticking, but it did seem like it wasn't smooth to flip around.

I'll give it a thorough cleaning anda look with some emery paper in hand. Can't hurt to polish that area up some... Thoughts before I screw something up?
__________________
My $0.02
nass is offline  
Old April 25, 2007, 08:02 AM   #6
benedict1
Senior Member
 
Join Date: July 26, 2006
Location: Southern California
Posts: 245
Take it out and check for any flashing on edges and file away if found.
Degrease completely with something like Gun Scrubber.
I shoot some degreaser down the priming ram interior to get any gunk off the inside of the ram where the lever mount. Blow dry with air.

If you wish, you can rub a little powdered graphite on the surface of the lever arm. Replace and it should be good to go.

Lots of crud comes out of cases when decapped and resized and any oil/grease in the lever arm area will eventually build up and cause erratic movement.

Be sure to lube the outside of the ram from time-to-time with 30W oil.

Last edited by benedict1; April 25, 2007 at 08:02 AM. Reason: Forgot a point.
benedict1 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:46 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06822 seconds with 9 queries