The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old September 17, 2006, 05:12 PM   #1
ledavatar
Senior Member
 
Join Date: July 27, 2006
Posts: 147
Accurate #2 Powder

I loaded some 9mm rounds of varying power using Accurate #2 and shot them in my Glock 19, but I noticed after a few rounds that it left little bits of sand colored powder residue lying around in the chamber. Is that normal? It doesn't look like it's good for the gun.
ledavatar is offline  
Old September 17, 2006, 11:17 PM   #2
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,564
When you get sandy residue left in the case/chamber/barrel, it's almost always unburned powder. Some causes are loose or no crimp, too low a powder charge for the caliber/bullet weight, or a weak primer (rare).

AA #2 is a good burning fast powder and usually burns well in the 9mm. Check to see if any of the above factors might be at fault.

Please give us some details of your loads: powder weight, bullet, primer, etc.
Mal H is offline  
Old September 18, 2006, 08:59 AM   #3
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 36,327
No matter what powder you use, you're virtually guaranteed of getting some unburned powder residue.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old September 18, 2006, 09:49 AM   #4
Ausserordeutlich
Junior member
 
Join Date: May 27, 2006
Posts: 996
I use AA#5 for 9mm and .45ACP reloading. I get a little soot, but not one grain of unburned powder.
Ausserordeutlich is offline  
Old September 19, 2006, 11:27 PM   #5
meinbruder
Junior Member
 
Join Date: September 19, 2006
Location: Portland, Oregon.
Posts: 3
RE--Accurate #2 Powder

I would like to echo that. .45acp loads are 8grs of AA#5 and 6grs of AA#2 behind a 240gr hard cast SWC from Oregon Trail with a CCI magnum primer. Standard taper crimp from Speer dies. 9mm, .38spl, .357mag, .44spl, and .44mag have all been loaded with the same powder and all showed the same problems, the revolvers got a solid roll crimp. Lots of smoke, okay the lube on the slug is burning, but lots of powder unburned in the guns and all over the bench in front of the shooting position on the line. I finally decided the powder was the problem and have switch over to WW231. Guess what? No unburned powder and a lot less smoke.

AA might meter like salt in a progressive loader but I don’t plan to use it again.
YMMV
Mike
meinbruder is offline  
Old September 20, 2006, 03:42 PM   #6
ledavatar
Senior Member
 
Join Date: July 27, 2006
Posts: 147
Now that I think about it, it's probably the weak loads doing this. I was experimenting with various loads that would be on the verge of cycling/not cycling the slide on a stock Glock 19. I will try some medium powdered loads (4.0gr Acc #2 on 115gr TMJ) by themselves and see how it does.
ledavatar is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:05 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06557 seconds with 9 queries