The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Gear and Accessories

Reply
 
Thread Tools
Old July 24, 2006, 09:55 PM   #1
Pecos21
Senior Member
 
Join Date: October 6, 2004
Location: East Texas
Posts: 186
Need help with Fobus holster

I bought a fobus holster for my P22. I have been practicing drawing, but have had no luck in removing the pistol from the holster. I've have tried the snappy movement as suggested in the instructions (i finally gave in and read them) with no luck. Everytime I just end up lifting my belt or pants up. There is no tension screw on the holster. Does anyone have any ideas?
__________________
Keep it safe...
Pecos21 is offline  
Old July 29, 2006, 08:40 AM   #2
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,270
stuck

Gently sandpaper the area inside the holster that secures the gun (normally around its trigger guard).
Test-draw frequently.

Chant "I can always take more off".
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old July 30, 2006, 12:58 PM   #3
f8lranger4x4
Member
 
Join Date: May 30, 2006
Posts: 62
I have one for my M9 Beretta and it is quite hard to get it out. I have found a slight twist while pulling will do the job.
f8lranger4x4 is offline  
Old August 10, 2006, 10:52 AM   #4
TacticalJunkie.com
Junior Member
 
Join Date: August 9, 2006
Posts: 14
RE: Holster problems

Once you break the holster in, it tends to get easier. I have one for my 1911 and it was hard at the beginning but it worked in. However if this does not work, I would recommend the sandpaper. If your uncomfortable with this method, try contacting fobus they have some great customer service.
__________________
Please visit my website and feel free to leave feedback or products you would like to see carried.
www.tacticaljunkie.com
TacticalJunkie.com is offline  
Old August 10, 2006, 11:53 AM   #5
MEDDAC19
Senior Member
 
Join Date: April 18, 2005
Location: Endless Mts,NEPA
Posts: 379
Have you tried silicone or WD-40 yet? I would lube it before taking away any material, once it gets loose you can't sand it back on.
MEDDAC19 is offline  
Old August 10, 2006, 12:07 PM   #6
Duxman
Senior Member
 
Join Date: February 16, 2005
Location: VA
Posts: 1,294
Armor all

Try Armor all.

I was having the same issue with my G34. On a Fobus.

If you armor all the inside of the Fobus - let it dry, then try drawing.

Its NIGHT and DAY.
Duxman is offline  
Old August 17, 2006, 10:14 PM   #7
silicon wolverine
Senior Member
 
Join Date: April 28, 2006
Location: South dakota
Posts: 674
+1 on armor all. also fobus rigs take awile to break in. Ive had mine for my G17 about three years now and its just getting to where i like it the best.

SW
silicon wolverine is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06688 seconds with 9 queries