The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old May 23, 2006, 08:08 PM   #1
PJH 980
Junior Member
 
Join Date: May 9, 2006
Location: SW PA
Posts: 5
new 22-250

i've been lurking around here for the past few weeks as i have started reloading about a month and half ago.

last week i bought a brand new rem. model 700 adl in 22-250 for $375. i put a 4-12 leupold on it and worked up some test loads for it. i got a lot of info from you all on here. you guys really are a great help.

my best load shot .71 inches at 100 yards. (50gn vmax, win brass, win. lg primer, 39.5 gns h380 2.345" overall length) i know thats nothing earth shattering, but i was pleased with the results of my first rifle reloads. i only loaded 6 different loads with the vmax and sierra 55 boat tail hollow points. all shot under an inch. i am going to load up some more test loads for the weekend.
'

anybody out there have any loads they like for this particular rifle?

again i'm new to reloading and am really enjoying the testing and working up loads process, as well as hanging out on here. can't wait until june when all the young woodchucks are on their own and i can start shooting.


thanks,
pat
PJH 980 is offline  
Old May 23, 2006, 08:47 PM   #2
ShuckersFan
Member
 
Join Date: March 1, 2006
Posts: 30
Slightly off subject, but where did you find a new ADL? Is it wood or synthetic?
ShuckersFan is offline  
Old May 23, 2006, 09:32 PM   #3
270Win
Senior Member
 
Join Date: August 30, 2005
Location: Damascus, Maryland
Posts: 921
I don't know about his, but two of my local WalMarts have them, both wood and synth (mostly synth) for $364 all day long. The only catch is, almost all of them are .270 or .30-06. I remember seeing one 7mm and one .223 ... the choices are limited.
270Win is offline  
Old May 23, 2006, 09:48 PM   #4
PJH 980
Junior Member
 
Join Date: May 9, 2006
Location: SW PA
Posts: 5
i got it at ace sporting goods in washington, pa. it was the only one they had left. all the other ones i have seen have been in 30-06 or 270 as well. i checked some of the other local gun shops as well and was not able to find a 22-250. i orginally asked if they had any in 223 but the only ones they had were the one 22-250 and some '06s and 270's. and to answer your question, it is a synthetic stock.

pat
PJH 980 is offline  
Old May 23, 2006, 10:11 PM   #5
Yuriens
Member
 
Join Date: February 1, 2006
Posts: 71
For my model 700 VSSF in 22-250 the most accurate powder/load combo by far has been IMR 4895, 55gr Vmax, CCI BR primers. I have worked up a lot of them but this one has .30-.40 inches over the others at 100 yards. Of course individual rifles will vary all over, but that is a good place to start.

Mike
Yuriens is offline  
Old May 23, 2006, 10:38 PM   #6
rwilson452
Senior Member
 
Join Date: June 10, 2004
Location: Tioga co. PA
Posts: 2,361
22-250 loads

With my Rem 700VLS I worked the powder in .2 grain increments. after finding the best load. I started tweaking the OAL in .005 increments. My best ever group was under .2 MOA ( .375 edge to edge) with 39.0 gr of H380 and the sierra 55gr. HPBT. the Sierra 55gr. BlitzKing came closest with 35gr of I4895.
rwilson452 is offline  
Old May 24, 2006, 12:08 AM   #7
918v
Junior member
 
Join Date: September 25, 2005
Posts: 1,372
55gr. Ballistic Tip
36gr. AA4064 or VV N-150 (full case unlike the other powders listed)
CCI or FC Primer
2.510" OAL

Half inch from 6 different rifles.
918v is offline  
Old May 24, 2006, 12:06 PM   #8
2400
Senior Member
 
Join Date: September 12, 2004
Location: AZ
Posts: 389
You will want to work up to this, starting at about 38.5-39gr of H-414.
I've had 2 different rifles shoot under 1/2" using 42gr H-414--Rem9 1/2M--WW brass--52gr HPBT@3856 FPS. My Ruger M77V will shoot .377 groups if I do my part at 100 yards and .512 at 200 yards. I just got some Nosler brass and I'll let you know if it makes a difference.
2400 is offline  
Old May 24, 2006, 03:00 PM   #9
PJH 980
Junior Member
 
Join Date: May 9, 2006
Location: SW PA
Posts: 5
thanks guys. i'll try some of those and see what happens.

pat
PJH 980 is offline  
Old May 24, 2006, 06:38 PM   #10
PJH 980
Junior Member
 
Join Date: May 9, 2006
Location: SW PA
Posts: 5
i got some time to mess around at the reloading bench and shooting bench after work toaday. i tried a few more loads and got some better results. with 39gns of H380 50gn vmax i was averaging groups of .601". i am pretty pleased with those loads right now, being that the 700 adl has a light barrel and the trigger could use some work. but, i am at least in the ball park for woodchucks now. i am going to shoot these rounds over my buddy's chrono.

thanks for all the info. i look forward to loading up some more loads you find to accurate.

pat
PJH 980 is offline  
Old May 24, 2006, 08:06 PM   #11
LAH
Senior Member
 
Join Date: March 22, 2002
Location: In The Hardwoods
Posts: 918
Congrats PJH 980............There's nothing wrong with a 3/4" group....Creeker
LAH is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07979 seconds with 9 queries