The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 28, 2006, 01:40 AM   #1
40MM
Member
 
Join Date: April 15, 2006
Posts: 69
Will My 9mm Dies Work On .38spl?

If not, will i need to get a new de-priming die, bullet seating die,powder loading die and a factory crimp die? Thanks!
40MM is offline  
Old April 28, 2006, 04:15 AM   #2
Tim R
Senior Member
 
Join Date: November 30, 2004
Location: God's side of Washington State
Posts: 1,601
No, Your 9mm dies will not work for 38 Spl. Normally, 38 Spl and 357 Mag use the same dies however. Also, your 9mm should have a taper crimp where as the 38 Spl/367 Mag normally use a roll crimp.
__________________
God Bless our Troops especially our Snipers.
Tim R is offline  
Old April 28, 2006, 09:16 AM   #3
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
If you are going to load .38 Special steadily, get the right dies. If you just want to load a box or two at rare intervals, you can get away with using the 9mm dies. You'll need a .38 Special shellholder and an alternate means of decapping.

The 9mm sizer will not deprime because you can only neck size with that die. If you happen to have a set of .223 dies and are willing to lube your cases, you can full length size and deprime .38 Special with that. The 9mm expander die and the seater will work fine once you have them properly adjusted.
Leftoverdj is offline  
Old April 28, 2006, 09:29 AM   #4
Russ5924
Senior Member
 
Join Date: February 18, 2005
Posts: 1,874
You can get a set of Lee Dies for under $30 so why mess with something that is half A--
__________________
Russ5924
Russ5924 is offline  
Old April 28, 2006, 09:58 AM   #5
Leftoverdj
Senior Member
 
Join Date: October 15, 2004
Posts: 934
Quote:
You can get a set of Lee Dies for under $30 so why mess with something that is half A--
A. You don't have $30
B. You need the ammo now, not when you can get the dies.
C. You only need one box for your worthless brother-in-law.
D. You have a flaming itch to see if it works.
Leftoverdj is offline  
Old April 28, 2006, 10:35 AM   #6
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,548
Actually, you may even be able to use the 9mm decapper if you can screw the decapping pin down far enough to reach the .38 spcl primer. I didn't test it, but it looks like my RCBS decapper has enough length to do that.

Going against intuition, the 9mm die has a slightly larger ID than the .38 spcl even though 9mm bullets are usually a few thou less in diameter. So I wouldn't load anything but light "plinking" loads. You won't get as tight a taper crimp as you would with a .38/.357 TC die. Therefore setback becomes more of an issue.
Mal H is offline  
Old April 28, 2006, 12:17 PM   #7
T. O'Heir
Senior Member
 
Join Date: February 13, 2002
Location: Canada
Posts: 3,452
No. Buy a proper die set. You won't need a separate crimping die though. Just the dies and a shell holder. For .38's, buy the .38/.357 set.
T. O'Heir is offline  
Old April 29, 2006, 08:10 AM   #8
beenthere
Senior Member
 
Join Date: November 16, 2004
Location: NE Indiana
Posts: 460
Loading

Tell the brother in law to buy you a set of dies for the next time and send him to Wally for some WWB this time.
__________________
The weak, and those unwilling to make the struggle, soon resign their liberties for the protection of powerful men or paid armies; they begin by being protected, they end by being subjected. Louis L'Amour
beenthere is offline  
Old May 1, 2006, 11:26 AM   #9
dakotashooter2
Senior Member
 
Join Date: January 13, 2005
Posts: 498
You should be able to decap with any die larger than the 38. ( Is this not what a "universal" decaping die does). Neck sizing and seating can be accomplished with the 9mm die. The seating die has a slightly larger diameter than the sizer die and in some sets the decaper can be screwed into it for depriming duty. I haven't tried it for the 38 but it might be a better "fit" than the "sizing " die for a limited run.
dakotashooter2 is offline  
Old May 3, 2006, 09:50 PM   #10
JJB2
Junior member
 
Join Date: December 14, 2005
Posts: 558
heck midway has speed dies for about $15!!! that's all i use to turn out great 9mm, .38 special, and .357 magnum reloads..... i've got two single stage presses side by side and with an extra die body i got from lee i get to use both presses at the same time... works for me!! check on em!!




LIFE IS SHORT..........
JJB2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 04:50 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08883 seconds with 9 queries