The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 6, 2000, 12:18 AM   #1
RHarris
Senior Member
 
Join Date: June 18, 2000
Posts: 416
I have seen the Lee Hand Press on their web site. Does this thing work very good?
RHarris is offline  
Old October 6, 2000, 10:20 AM   #2
Bogie
Senior Member
 
Join Date: June 5, 2000
Location: Job hunting on the road...
Posts: 3,827
I use mine with their collet dies. Very nice for my varmint and long range rifles...

Bogie is offline  
Old October 6, 2000, 11:44 AM   #3
saands
Senior Member
 
Join Date: November 14, 1999
Posts: 1,563
I have been using one for about ten years. For cases that resize easily and for people that place a premium on not having to have a permanent table set up (apartment/condo) they work very well. About 6 months ago I started doing my resizing on a vise mounted press in the detached one-car garage. Then I return to the comfort of the kitchen table in the condo to do the rest with the hand press. I never had any problems with .40's and .357's ... but .308's and for some strange reason 9mm's require a bit more work and drove me to buy Lee's simplest bench type press.
Hope this helps,
Saands
saands is offline  
Old October 6, 2000, 12:37 PM   #4
freedomlover
Guest
 
Posts: n/a
Mine works great for reloading calibers. Haven't used it for calibers yet. Hope to start reloading .308 soon though. Can't beat it for the price ($27 from Midway).

freedomlover
 
Old October 6, 2000, 12:41 PM   #5
freedomlover
Guest
 
Posts: n/a
Just realized my computer's Cyber Sitter edited that post for me. I should have said I haven't used if for "long arm" calibers yet, but it works great for "revolver" calibers.

freedomlover
 
Old October 6, 2000, 05:47 PM   #6
Robert Foote
Senior Member
 
Join Date: December 31, 1998
Posts: 623
Have had one for ten-plus years now, used it a lot for pistol calibers and .30-06 as well. Broke a handle which I replaced; my fault for insufficient lube on an '06 case at the time. I got another one for my daughter as I would like to get her going on loading her own 9mm ammo--so I don't have to do it. Good tool--wouldn't be without it just for the convenience.

------------------
Robert Foote is offline  
Old October 8, 2000, 06:01 PM   #7
Big Bunny
Senior Member
 
Join Date: August 9, 1999
Location: New South Wales - Australia
Posts: 605
The Lyman 'TONG-TOOL' is another lower-volume reloader recommended for muscle building !Don't forget the 'lube!
The 'LEE LOADER' for shot-gun and pistol is also good and very portable-[but not available for FLS of centrefire of course,l neck sizing is OK] ...uses a mallet.

Vice crush-dies are another low cost FLS for rifle bottle-neck cartridges re-sizing.

Higher volumes do need a proper bench set-up I feel.
BB

------------------
If we shooting sportspersons don't hang together... we will all hang separately !
Never knock another's different shooting interest or discipline...REMEMBER we are all but leaves on the same tree of freedom.
Big Bunny is offline  
Old October 8, 2000, 11:41 PM   #8
MrMisanthrope
Senior Member
 
Join Date: October 6, 2000
Location: Spokane WA
Posts: 121
The BIG question is, will the Lee Hand Press handle the double crimp necessary for my ungodly compresed .454 loads?

350gr LBT hard-cast WFN
31gr 296 or H110
sm mag rifle primers
Taper AND roll crimp (so they don't jump after 1 or more 2200ftlb sisters go boom...)

------------------
_______________________

HONOR PRAE OMNIBUS
INIURIA MINIMA OMNIBUS
****
Honor Before All
Doing Least Harm Always
_______________________


[This message has been edited by MrMisanthrope (edited October 09, 2000).]
MrMisanthrope is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 01:03 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.08104 seconds with 9 queries