The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old April 11, 2001, 03:04 PM   #1
high_caliber
Senior Member
 
Join Date: August 22, 2000
Location: Louisville, Ky., USA
Posts: 107
I've just started reloading this caliber. I bought a new RCBS die set and noticed that the crimp die does taper crimps. Should I consider getting a roll crimp die or is it something I can live without?
high_caliber is offline  
Old April 11, 2001, 04:02 PM   #2
Mike Irwin
Staff
 
Join Date: April 13, 2000
Location: Northern Virginia
Posts: 35,877
Roll crimps are really necessary only for the heaviest magnum loads, in my experience.

If you start having problems, get a roll crimp die. Until then, though, use the taper crimp die. Your brass will last longer.
__________________
"The gift which I am sending you is called a dog, and is in fact the most precious and valuable possession of mankind" -Theodorus Gaza

Baby Jesus cries when the fat redneck doesn't have military-grade firepower.
Mike Irwin is offline  
Old January 2, 2006, 04:30 PM   #3
Daniel BOON
Senior Member
 
Join Date: June 5, 2005
Location: Henderson NV
Posts: 360
My favorite caliber

I shoot a 357 revolver (several differ makes). I haven't had much luck with seating/crimping working; soooooo I bought redding roll crimp die and put a healthy crimp on every thing. seems to work for me.......
Daniel BOON is offline  
Old January 2, 2006, 04:48 PM   #4
Peter M. Eick
Senior Member
 
Join Date: August 3, 1999
Location: Houston, Texas
Posts: 2,877
I use a Redding Profile crimper also for 357 mag and really like. I have to admit that it took me until recently to figure out that my 357 mag die is a taper crimp also. I had never used it because of the redding so I did not even notice.
__________________
10mm and 357sig, the best things to come along since the 38 super!
Peter M. Eick is offline  
Old January 2, 2006, 04:58 PM   #5
MADISON
Senior Member
 
Join Date: January 1, 2000
Location: Roanoke, Virginia
Posts: 2,678
Which crimp for .357 Magnum?

I have been loading for 35 years and using a TAPER CRIMP for 18+ of thoose years. A taper crimp takes the flare out of the brass. To give you an example:
Unless they dies are LEE or HORNADY, you can remove the decapping stim from the sizing die; readjust the die and you have/are taper crimping.
Adjusting may take a little time....
MADISON is offline  
Old January 2, 2006, 07:37 PM   #6
JDG
Senior Member
 
Join Date: November 28, 2005
Location: West Michigan
Posts: 673
I use Lee dies, and have never had a problem seating and roll crimping at the same time. I roll crimp if the bullet has a crimp groove, tapper crimp if it dosnt. JDG
JDG is offline  
Old January 3, 2006, 06:26 AM   #7
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,204
all my revolver crimping

Redding Profile Crimp die; WILL enhance accuracy and consistency; proven.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Old January 3, 2006, 09:16 AM   #8
RERICK
Junior member
 
Join Date: July 9, 2005
Posts: 369
I use the Lee factory crimp die.I get nice consistant crimps and case length isn't such a problem as it is with regular roll crimp dies.It will also enhance accuracy.Some drive Chevy some drive a Ford

Last edited by RERICK; January 3, 2006 at 04:19 PM.
RERICK is offline  
Old January 3, 2006, 04:45 PM   #9
Rivers
Junior member
 
Join Date: November 5, 2005
Posts: 670
RCBS also makes a three-die set that roll-crimps. You got the wrong set, unless you're reloading for a semi-auto.
Rivers is offline  
Old January 6, 2006, 06:22 AM   #10
WESHOOT2
Senior Member
 
Join Date: February 20, 1999
Location: home on the range; Vermont (Caspian country)
Posts: 14,204
I currently have 40 die-sets for handgun ('cause that's all I do)

IMNSLE the Redding Profile Crimp die is the finest crimping die for revolver-intended ammo.

I use LEE, Lyman, RCBS, Dillon, Hornady, and Redding dies.
__________________
.
"all my ammo is mostly retired factory ammo"
WESHOOT2 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:33 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07408 seconds with 9 queries