The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old March 30, 2000, 08:01 PM   #1
Dave AA
Senior Member
 
Join Date: August 18, 1999
Posts: 387
Hey guys,
I'm loading .45ACP with 200grn SWC. I switched from swaged lead to copper coated, same OAL, 1.221". Now, the lead fed perfectly, but the copper coated catches the feed ramp, and knocks the bullet back into the case. (out of a Kimber 5") I'm keeping the copper coated bullets, the lead was just too nasty, so I need to make this work! Help, Help!
Dave AA is offline  
Old March 30, 2000, 08:03 PM   #2
Bud Helms
Staff
 
Join Date: December 31, 1999
Location: Middle Georgia
Posts: 13,005
Neck tension. Taper crimp adjustment. Polish feedramp.

[This message has been edited by sensop (edited March 30, 2000).]
Bud Helms is offline  
Old March 30, 2000, 08:25 PM   #3
Dave AA
Senior Member
 
Join Date: August 18, 1999
Posts: 387
Feed ramp polished, having a hard time adjusting crimp. Using a Dillon SDB. Does the OAL have something to do with this?

[This message has been edited by Dave AA (edited March 30, 2000).]
Dave AA is offline  
Old March 30, 2000, 08:57 PM   #4
Svt
Junior member
 
Join Date: January 23, 2000
Posts: 467
Dave,
I use Rainer Copper Coated 200 gr SWC with an OAL 1.240 CRIMP is .470

It fires perfectly through all but one of my 1911's. My Colt Gold Cup doesn't feed SWC at all

Check your crimp.
Svt is offline  
Old March 30, 2000, 10:23 PM   #5
Dave AA
Senior Member
 
Join Date: August 18, 1999
Posts: 387
Alrighty, let's see, I'm using West Coast Bullets, 200 grn, but if I seat the bullet shallower, it doesn't look like it has enough bearing surface.........
Ok, bullet length is .621-.625" how does this compare?
thanks for the help!
Dave AA is offline  
Old March 30, 2000, 10:58 PM   #6
alan
Senior Member
 
Join Date: June 7, 1999
Posts: 3,745
Dave AA:

Consider the following. Go back to the lead, cast bullet, hard cast, H & G 68 (or similar).

Try an oal of 1.260. Diameter of loaded round, at end of cartroidge case, after TAPER CRIMPING, thould run aproximately .470" diameter.

I shoot this type of load in 2 45 auto's, one a Colt 70 series government model, the other a Kimber Classic Custom Target. It feeds fine in both.

I also wonder as to what it is in particular that troubeles you about lead bullets, though ones personal preference is of course ones personal preference. The SWAGED LEAD BULLET might be so soft that it is causing a problem, or problems.
alan is offline  
Old March 30, 2000, 11:51 PM   #7
char923
Senior Member
 
Join Date: February 18, 2000
Location: Anchorage AK
Posts: 237
Pay alittle more and get hard cast
bullets,swaged bullets lead barrel bad if velocity is to high. play with your OAL. I load my to 1.250" And all works fine.
char923 is offline  
Old March 31, 2000, 12:07 AM   #8
PDshooter
Senior Member
 
Join Date: March 30, 2000
Location: Illinois (PRI)
Posts: 599
Hi Dave, I shoot colt 45. H&G 68 bullets that I cast. OAL.is 1.24 (5.8 gr W231) How new is your gun? Sometimes auto need brake in time 100to200 hard-ball? I would seat your bullets out more, and a little crimp. Jeff
PDshooter is offline  
Old March 31, 2000, 09:41 AM   #9
JimK
Junior Member
 
Join Date: April 18, 1999
Location: mi
Posts: 9
Check the dia. of your expander button I believe the expander for cast bullets is a bit larger than one for jacketed bullets and the West Coast bullets are sized .451 same as most jacketed bullets

Jim
JimK is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:17 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07581 seconds with 9 queries