The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old February 12, 2000, 07:14 PM   #1
mattfra
Member
 
Join Date: July 3, 1999
Posts: 93
This is an update for those of you who helped me decide what press to buy. As a "newbie" I went into this new hobby of reloading knowing nothing! I did go with the Lee 35th Anniversary Kit (single stage press) and then purchased the Lee "Speed Die" for .45 ACP. Today I loaded up 5 rounds (just for test sake) with Bull-X LSWC bullets and 6.7 grains Hodgdon Universal Clays powder. I went back into the woods and set up a target (heart was pounding quickly by this time). I loaded up the Ruger P90 and...bang, bang, bang, bang, and bang!! Five rounds, no feeding or ignition problems. Ok, NOW I AM HOOKED! I think I'll try 6.9 grains next! Yee-Haw!
mattfra is offline  
Old February 12, 2000, 08:01 PM   #2
HankL
Senior Member
 
Join Date: March 11, 1999
Location: The Sunny South
Posts: 2,174
mattfra, what grain bullet is that Bull-X? I've never used Clays powder but the Hodgdon book #26 list 4.9 grains as MAX for a 185 gr. JHP

Just curious,
Hank
HankL is offline  
Old February 12, 2000, 09:30 PM   #3
MrGreenMachine
Member
 
Join Date: January 22, 2000
Location: East Tenn
Posts: 20
So what did your whole setup end up costing? I seem to remember you wanted to stay on the inexpensive side.
MrGreenMachine is offline  
Old February 12, 2000, 09:56 PM   #4
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,541
Hank, I think you may be thinking of plain Clays, not Universal Clays. U. Clays is several slots down the burn rate chart from Clays. 6.9 grains sounds like a reasonable charge for UC.

I have often thought Hodgdon should not have made 3 distinctly different powders sound so similar - Clays, International Clays and Universal Clays.
Mal H is offline  
Old February 12, 2000, 10:08 PM   #5
Bud Helms
Staff
 
Join Date: December 31, 1999
Location: Middle Georgia
Posts: 13,005
Go, Mattfra!
Bud Helms is offline  
Old February 13, 2000, 02:14 AM   #6
Coinneach
Staff Alumnus
 
Join Date: February 23, 1999
Location: Denver, CO
Posts: 4,273
Mattfra, welcome to your new addiction.

------------------
"If your determination is fixed, I do not counsel you to despair. Few things are impossible to diligence and skill. Great works are performed not by strength, but perseverance."
-- Samuel Johnson
Coinneach is offline  
Old February 13, 2000, 09:05 AM   #7
mattfra
Member
 
Join Date: July 3, 1999
Posts: 93
HankL and others that replied,

Yeah, I forgot to mention what size bullet. It was 185 gr LSWC from Bull-X. The little Hodgdon Booklet that comes with the kit listed using a JSWC with 7.2 Universal Clays, so being a beginner and wanting to keep both eyes and 9 fingers, ah, I mean 10 fingers I backed it off a bit to 6.7gr.
I paid $67.99 for the Lee 35th Anniv. Kit and $13.99 for the .45ACP speed die from MidwayUSA...no shipping/tax. So about $82 for the kit/die and 100bullets, primers, and 1lb of powder $41.50. A grand total of $124!! The kit comes with a priming hand tool, scale, sizing lube...etc. I just had to buy primers, bullets and powder. Their site is www.midwayusa.com I get their catalog every month. The kit is on sale for February through Feb 29. Thanks again to all for the encouragement and advice on reloading!!

[This message has been edited by mattfra (edited February 13, 2000).]
mattfra is offline  
Old February 14, 2000, 03:41 PM   #8
jtduncan
Senior Member
 
Join Date: December 5, 1999
Location: Seattle, Washington, USA
Posts: 1,681
Universal is a real clean burning powder and I use it with my 230 grains at 5.7 grains per case. Medium speed powder. Little if any muzzle flash. I like it!

------------------
The Seattle SharpShooter
jtduncan is offline  
Old February 14, 2000, 11:05 PM   #9
bfoster
Senior Member
 
Join Date: October 13, 1998
Location: N. of Fords Switch, OK, USA
Posts: 297
I agree with Mal H regarding Hodgdon's naming of three distinct powders using the word "Clays" in each. I think that this may eventually contribute to an accident through simple failure of communication.

I strongly recommend listing the ADI numbers along with Hodgdon's names:

Clays= AS30N

International Clays= AS50N

Universal Clays= AS70N and/or AP70N

Bob
bfoster is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:59 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.09279 seconds with 9 queries