The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old December 4, 1999, 03:00 AM   #1
jbyrd
Junior Member
 
Join Date: July 14, 1999
Posts: 9
I am reloading military brass and I have a question that I have to ask. I am using a primer pocket reamer by hand on once fired 223 military crimped brass. When I have finished the primer pocket appears to be a little off center but the primers seat nice and tight. I'm using 25 grains of IMR 4064 with a 55 grain FMJ BT.
What kind of problems could I encounter? Any major safety concerns? Is there a better way to remove the crimp?
Any comments would sure be appreciated.
jbyrd is offline  
Old December 4, 1999, 08:08 AM   #2
Fred S
Senior Member
 
Join Date: July 2, 1999
Location: New Baltimore, MI
Posts: 569
Hi:

I use a Dillon Super Swager to remove crimps. Its works well and uniform. It is a bit ob the expensive side, but quality tools are quality tools.

I think you might be risking poorly seated primers. You may get a high primer someday or maybe one may fall out. When reloading high power cartridges you should be ensuring everything is done right. if it doesn't look or seem right, it probably isn't.


Take care.

Fred
Fred S is offline  
Old December 4, 1999, 09:02 PM   #3
GreybeardB
Member
 
Join Date: June 23, 1999
Posts: 58
jbyrd,

Your load sounds OK but, an off center primer pocket ? Hmmmmmmm .

Do you have a hand drill..... or better yet a drill press ?

Use a "military" type decaping die to keep from breaking pins, then use about a 1/4 in. drill bit in youre drill press to remove the crimp.

You may have to alter the bit's cutting angle slightly on a grinding stone, but it will take out a three point pinch or rolled type crimp..... it will not make your primer pocket off center.

You need only to remove the crimped metal, be careful not to remove any part of the pocket wall.

Youre only reason for this tedious operation it to alow a new primer to ENTER the pocket freely.

OPEN OR OUT



------------------
Ralph in In.

GreybeardB is offline  
Old December 4, 1999, 09:11 PM   #4
swifter...
Senior Member
 
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
I had a lot of success removing the crimp by using a case-mouth deburring tool. Which end is pretty obvious, just be sure to not cut too much. It seems to be self-centering, too...



------------------
The Bill of Rights, and the Golden Rule are enough for civilized behavior. The rest is window dressing. Shoot carefully, swifter...

swifter... is offline  
Old December 5, 1999, 05:14 PM   #5
Joefo
Senior Member
 
Join Date: March 22, 1999
Location: NY
Posts: 165
Get a regular cutter from Lyman or others that fits in a power screw driver. They work real nice and only cut the crimp. I think they are around 6 bucks.

Joefo
Joefo is offline  
Old December 6, 1999, 11:37 PM   #6
jbyrd
Junior Member
 
Join Date: July 14, 1999
Posts: 9
Thanks guys for the info. I think I understand the crimp a little better now. It seems like I am removing the crimp from one side of the pocket. I thought the crimp extended the full length of the pocket. Not so apparently. Again thanks.

------------------
"To disarm the people is the most effectual way to enslave them." George Mason
jbyrd is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:26 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07544 seconds with 9 queries