The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old November 12, 1999, 03:17 PM   #1
BenDover
Member
 
Join Date: October 14, 1999
Location: San Diego, CA. USA
Posts: 51
I was drawn between IMR-3031 or Winchester 748. Any opinions?
BenDover is offline  
Old November 12, 1999, 04:03 PM   #2
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
I prefer the 748 simply because it meters better, not to mention that I happen to get better results with it (with 150, 165, & 180 grainers). What grain of bullet are you using?

Jack
Jack Straw is offline  
Old November 12, 1999, 04:49 PM   #3
BenDover
Member
 
Join Date: October 14, 1999
Location: San Diego, CA. USA
Posts: 51
Jack,
I'm still working up loads for my M1-A. I still have not shot any loads yet.....very soon!
I'm trying out 147 FMC, 165 Nosler BT and Seirra 168 Matchkings. Do you have any preferences. Thanks...Steve
BenDover is offline  
Old November 13, 1999, 01:20 AM   #4
Deputy Al
Junior Member
 
Join Date: November 12, 1999
Location: Moreno Valley, CA USA
Posts: 5
I used 45.5 grains of WW-748 with the Sierra 168 grain Matchkings and WLR primers to duplicate the Federal Match ammo specs in our SWAT sniper guns. These were put up in Federal cases, and shot as well as the factory stuff, which sometimes did 1/4" to 3/8" 5-shot groups @ 100 yards. Good stuff!
Deputy Al is offline  
Old November 13, 1999, 01:45 AM   #5
alan
Senior Member
 
Join Date: June 7, 1999
Posts: 3,720
Remington's target load, that they used with their 40x rifles was, as I recall, 37 grains of 3031 with a 168 grain bullet, they did not say whose. Factory target showed 3-5 shot groups that averaged .43", indoord at 100 yards. I used this load with Hornady 168 grain Match bullets at 600 yards, and was quite surprised. The load shot very well, and there was almost no discernable recoil.

You might also try WC 846 with 168 or 173 grain FA match bullets, if you can find any. I used 41- 42 grain charges in bolt rifles, for 200 and 300 yard stages of NMC course. 748 should work well enough, however I have never used any of it.
alan is offline  
Old November 14, 1999, 12:31 PM   #6
TheOtherMikey
Senior Member
 
Join Date: October 16, 1999
Location: Surprise, Arizona, USA
Posts: 171
I use both 748 and 4895 to reload .308 and 30-06, both with good results. Mikey
TheOtherMikey is offline  
Old November 15, 1999, 03:05 AM   #7
Cheapo
Senior Member
 
Join Date: November 19, 1998
Posts: 986
748 is absotively fantabulous for the .308 & 7.62 NATO loadings. Using Lake City brass (heavier & less internal capacity than Fed., =higher pressures), I use 43.5 and get sub-inch groups!
Cheapo is offline  
Old November 17, 1999, 09:55 PM   #8
Paul B.
Senior Member
 
Join Date: March 28, 1999
Location: Tucson, AZ
Posts: 2,534
According to an article, a while back, in one of the gun magazines, the representatives of the various suppliers were asked which of their companies powders was best for the .308 Win./7.62 NATO. I don't remember IMR's response, but Winchester's was an emphatic W-748. He said it was THE powder designed for the .308. I haven't tried it, having pet loads using
W-760, but I just got an 8 lb. cannister of W-748, so I will be trying it soon.
I think IMR said 4895 was the powder they felt was best, but I am not sure.
Paul B.
Paul B. is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 03:35 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2013 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07906 seconds with 9 queries