The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old October 27, 1999, 10:54 PM   #1
TLH
Member
 
Join Date: June 6, 1999
Posts: 42
Does anyone have a good load for a 240 lead SWC to get it, in a magnum case to between 900 -950 FPS in a 4" tube ??
I know I can load the 44 Spl. but would rather use magnum cases. To make it more interesting I'm looking for a ball powder load so it will go smoothly in my Dillon press.
TLH is offline  
Old October 28, 1999, 12:58 AM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,417
I'm feeling lazy, right now, so I'm not gonna go to "The Book". Howsomever, I used to load 5.8 gr. of 231 behind a 200-gr. .45ACP, 5" barrel to get 850 ft/sec. So, I'd guess around 7 gr. of 231 in the shorter barrel and the heavier bullet would put you in the ball park.

I used the 5.8 grain powder charge (too lazy to change the powder measure) behind 250-gr lead bullets in my Red Hawk, but that has the 7-1/2" barrel. It definitely knocked down steel plates harder than the .45 Gummint...

Go buy a book!

, Art
Art Eatman is offline  
Old October 28, 1999, 01:15 AM   #3
zot
Senior Member
 
Join Date: April 2, 1999
Location: U.S.A.
Posts: 566
Winchester olin powder company has a PDF
download for all their powders,Adobe Acrobat
reader download,it'll fit on a floppy too,
from Speers 13th manual
HS-6 8.5 gr. 822 fps
231 6.0 gr. 808 fps
buy a book:}
zot is offline  
Old October 28, 1999, 09:11 AM   #4
TLH
Member
 
Join Date: June 6, 1999
Posts: 42
Thanks guys, actually have about 10 or so different manuals from the last 30 years.
The books list loads that when you run them accross a chronograph doesn't really produce what they say they will ... just hoping somebody had a pet load <G>
TLH is offline  
Old October 28, 1999, 12:45 PM   #5
Jack Straw
Senior Member
 
Join Date: July 26, 1999
Location: Georgia
Posts: 362
I've gotten great results using 8gr of Unique and a 240gr SWC (7.5 inch barrel and mag cases). Obviously its not a ball powder, but it still feeds well through my Dillon. Its a fun and accurate load in my guns.

Jack
Jack Straw is offline  
Old October 28, 1999, 05:47 PM   #6
plateshooter
Senior Member
 
Join Date: September 29, 1999
Location: N.E. Ohio
Posts: 522
I use 6.7 gr of Red Dot with the 240 gr SWC, home cast, and lubed with Lee liquid alox. Per Ed Harris, the Red Dot isn't as position sensitive as some of ball powders. I've used this load for several years for plates and it's accurate and consistant for me.
Good shootin to ya
plateshooter is offline  
Old October 29, 1999, 08:44 AM   #7
fal308
Staff Alumnus
 
Join Date: October 12, 1998
Location: Missouri
Posts: 1,986
Again not a ball powder but I use 9.5 gr of Vihtavouri N350 with a 200 LFN. Haven't chrono'd it but it's a pussycat. This is my cowboy load.
fal308 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:31 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06864 seconds with 9 queries