The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old August 31, 1999, 05:39 PM   #1
CRASH36
Junior Member
 
Join Date: April 2, 1999
Location: Atlanta , GA
Posts: 11
I have just purchased some new 255g 45LC Cowboy lead bullets to load for my blackhawk. I have never loaded "lead" bullets before, and Hornady seems to not want to give out any "free" info on this stuff.
I have a few questions about lead bullet loading if someone has some time to help
#1 Do you load lead bullets the same as you do with Jacketed bullets?, Do the lead bullets require some sort of a "wad" between the bullet and the powder?
#2 What is a "Gas Check", and do i need one?
#3 Do you have any loading info reguarding these 255g lead bullets that will work with standard powders like Unique or Blue Dot?
Any help would be great!, Thanks CRASH36
CRASH36 is offline  
Old August 31, 1999, 07:01 PM   #2
swifter...
Senior Member
 
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
You might want to bell the case mouth a tad more, otherwise its about the same. No wad is needed, and could even be dangerous.
Gas checks are little copper caps that fit to the base of a bullet. Generally, the bullet is cast in a "gas check" mould.
i use both Unique and BlueDot in my .45LC. Check the manual, you should find a bullet about that weight, jacketed or not, lead has a greater lubricity and you should'nt have any trouble.
8 Gr Unique is nice and mild.
12 gr Blue Dot is at the bottom of the "RUGER & TC" loads.




------------------
The Bill of Rights, and the Golden Rule are enough for civilized behavior. The rest is window dressing. Shoot carefully, swifter...

swifter... is offline  
Old September 1, 1999, 06:29 AM   #3
CRASH36
Junior Member
 
Join Date: April 2, 1999
Location: Atlanta , GA
Posts: 11
Thanks for the help SWifter, Im gonna try and load a few "Mild to start" shells today. I assume that because you didnt expand on the "gas Check" question, That means i do not need them. Ill let ya know how they turn out. CRASH#^

------------------
The secret to life is very simple; You get back what you put in, And people get what they deserve.

[This message has been edited by CRASH36 (edited September 01, 1999).]
CRASH36 is offline  
Old September 1, 1999, 09:17 AM   #4
Quantrill
Senior Member
 
Join Date: February 28, 1999
Location: Arizona, USA
Posts: 725
I believe that gas checks [GC] are not permitted in SASS shoots, just plain base bullets. I have found that "gas check" bullets can be shot without the gas check with acceptable results, but plain base bullets normally can't have GC's put on them although you could mount them upside down I suppose. Quantrill
Quantrill is offline  
Old September 1, 1999, 11:16 AM   #5
JoeHatley
Senior Member
 
Join Date: July 1, 1999
Location: Iowa
Posts: 2,135
CRASH36,

Here ya go:
http://reloading.atk.com/interactive...cfm?nGunType=4

Or go to: www.alliantpowder.com and then navigate to the reloading/cowboy section.

Good luck...

Joe





------------------
Go NRA
JoeHatley is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 11:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06649 seconds with 9 queries