The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 18, 1999, 09:50 PM   #1
MogulRun
Junior Member
 
Join Date: January 13, 1999
Posts: 2
I need a little help. I've started to reload 22/250 ammo for a friend. When I resize the brass it seems to be tight when loaded in the rifle. Should I set the die a little deeper to resize more, then check the round in the gun ? Or is it normal for once fired brass to be a little tight ? The ammo will only be used in his gun. What is the correct way to resize for usage in one gun ? Also a few empty cases he has giving me have splits in the brass. They were factory loads, and were not reloaded. Is this normal with this gun ?
I've done a lot of reloading for my 9mm and 45acp but the rifle reloads has me a little confused.
Thanks for your help
MogulRun is offline  
Old June 19, 1999, 08:10 AM   #2
flatlander
Senior Member
 
Join Date: June 16, 1999
Posts: 120
Where were the factory loads splitting? If the neck of the case was split, it could be old cases that got brittle. I've seen that with old 30-'06 factory loads. You need a way to check the headspace on some of your friend's fired brass against the sized cases to see if you're setting the shoulder back to where it needs to be for easy chambering(this will also help you avoid setting it back too far, which will reduce case life). The easiest way I know of is to use the Stoney Point tool made for this. You need a vernier caliper to install this tool on, but once you have the setup, you can measure just about any bottleneck case. The old advice to screw the FL die into the press until the shellholder contacts the bottom of the die when the ram is raised is, well, not a very exact way to do anything. Different shellholders from the same manufacturer will give different degrees of sizing when using this method. Redding even makes a set of shellholders with different thickness so you can adjust the amount of sizing. Also, older brass that's harder will "spring back" from sizing more than newer, softer brass, and this could be causing some of your problem. Good luck.
flatlander is offline  
Old June 19, 1999, 08:57 AM   #3
dundee
Senior Member
 
Join Date: December 6, 1998
Location: mytown,mi,usa
Posts: 162
2 thoughts; with the factory cases splitting ?? how many are split, where are the splits, are they of only one headstamp?
What make of rifle/barrel? is this a custom or other make that could have a out of spec chamber?
#2 the reloaded round should not be a tight fit in the chamber. Normally adjustment of the resixing die in the press until the resized case enters the chamber freely is a good fit of the case to that chamber.
dundee is offline  
Old June 19, 1999, 08:58 AM   #4
Little-e
Senior Member
 
Join Date: May 20, 1999
Posts: 171
I don't know if I have quite enough experience to be giving advice but here it goes anyway. Check the length of the cases. Rifle brass will stretch alot more than pistol so your problem may be as simple as the cases being too long. Both max. case length and trim length should be in your reloading manual.
Little-e is offline  
Old June 19, 1999, 10:49 AM   #5
Don Morgan
Member
 
Join Date: June 2, 1999
Posts: 43
I have to agree with Flatlander and Dundee, but there are some another test you may want to consider. Take an empty 22-250 case and slide it into the chamber to see if it fits just snug, then eject it out and look for markings on the case. If this is a Custom Match Grade Barrel you will have a very tight fit, if it is not then the chamber may not of been large enough from the factory and it needs to be looked at by a gun smith.

------------------
Society is safer when the criminal does not know who is armed

Don Morgan is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 10:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06352 seconds with 9 queries