The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old June 9, 1999, 05:35 PM   #1
KAM_Indianapolis
Senior Member
 
Join Date: February 3, 1999
Location: Indianapolis, IN, USA
Posts: 612
Just started using my new reloader yesterday. This is also the first time I've ever reloaded.

The cases seem to be getting crimped real bad on one side. Happened to about 5 bullets out of 30. It looks like the case collapsed on one side. Didn't change anything between the good and bad ammo.

These are once fired Win 9mm Brass. De-primed and sized. Then cleaned with a corncob medium. After that I made sure there was no corncob left in. Primed them, flared and filled with powder (4.6g Bullseye), then pressed the bullet in (115g FMJ).

Don't know if I'm doing something wrong, or have something setup wrong.

Any help would be appreciated.

Thanks...
Keith
KAM_Indianapolis is offline  
Old June 9, 1999, 08:42 PM   #2
Art Eatman
Staff Lead
 
Join Date: November 13, 1998
Location: Terlingua, TX, USA
Posts: 22,540
When you set your de-capping/expander die for depth, did you adjust it to provide a very slight "bell" of the case mouth?

It should be belled just enough such that the bullet will barely fit inside the case mouth.

Then, as you seat the bullet, the seating die should be set up such that the crimp or taper-crimp part of the die swages the bell back down to the proper diameter.
Art Eatman is offline  
Old June 9, 1999, 08:53 PM   #3
Grayfox
Senior Member
 
Join Date: December 17, 1998
Posts: 1,885
Several posabilities just off the top of my head.

Not enough flare on the case mouth. The bullet could be hanging on the edge.

Crimp die is adjusted too tight.

Cases are too long. This isn't very likely with the 9mm as they seldom need trimming. But should be checked anyway.

You didn't say if all the cases are the same brand. Some are a little thicker than others and may not crimp properly if the reloader is set up for another brand. Check to see if one brand is giving you problems. If so, load them seperately after reseting the dies.

Grayfox is offline  
Old June 9, 1999, 09:19 PM   #4
Mal H
Staff
 
Join Date: March 20, 1999
Location: Somewhere in the woods of Northern Virginia
Posts: 14,520
Some more possibilities:

Are you trying to seat the bullet too deep? If so, the crimp ring may be trying to crimp while the bullet is still going in. What is the OAL you are going for?

Are the bullets set on the casings straight up and down before starting to seat? If they are canted too far, the seating die won't be able to straighten it out before damaging the casing.

Mal H is offline  
Old June 11, 1999, 11:25 AM   #5
Cheapo
Senior Member
 
Join Date: November 19, 1998
Posts: 986
Or perhaps an even simpler cause, if I understand the problem correctly (pictures scanned into the old 'puter would help a lot).

Is the bullet tipping over as you run the ram up? I like to use the minimum mouth belling possible, which means that sometimes a short case doesn't get quite enough and it loses its grip on the bullet base before seating begins.

So, I often guide the case/bullet up into the die. Once in there, the bullet can't tip over and catch the case mouth. With my dies at least.
Cheapo is offline  
Old June 12, 1999, 08:25 PM   #6
KAM_Indianapolis
Senior Member
 
Join Date: February 3, 1999
Location: Indianapolis, IN, USA
Posts: 612
Thanks for the help. I've been a bit busy but will be trying your suggestions tomorrow (Sunday). If that doesn't help I'll scan some pics in to help with the diagnoses.

Peace...
Keith
KAM_Indianapolis is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:22 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06657 seconds with 9 queries