The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > Handloading, Reloading, and Bullet Casting

Reply
 
Thread Tools
Old January 4, 1999, 10:20 AM   #1
GuyM
Member
 
Join Date: January 4, 1999
Posts: 17
Can anybody give me their recommendations for a good clean burning powder for 9mm and 45 auto pistols. I am presently using Bullseye and it seems rather dirty. Also, what is a good mail order source for powder, primers and bullets?

Thanks
GuyM is offline  
Old January 4, 1999, 10:52 AM   #2
fal308
Staff Alumnus
 
Join Date: October 12, 1998
Location: Missouri
Posts: 1,986
Currently use Vita Vourhi N350. Also liked W231.
fal308 is offline  
Old January 4, 1999, 12:40 PM   #3
Bob Thompson
Senior Member
 
Join Date: December 28, 1998
Location: riverdale,ut,usa
Posts: 136
I have been using Universal clays for some time now for 9mm, 44 Special and 45 auto and have had good results. It will achive max. velocity and is clean burning. Approximately same burninmg rate as Unique, my old standby.
Bob Thompson is offline  
Old January 4, 1999, 08:27 PM   #4
Plainsman
Member
 
Join Date: October 31, 1998
Posts: 34
HP-38 is another good one! Similar to the W-231!
Plainsman :-)
Plainsman is offline  
Old January 4, 1999, 11:02 PM   #5
Grayfox
Senior Member
 
Join Date: December 17, 1998
Posts: 1,885
In 9mm try Win 231. For .45 target loads try Win Super Target (WST). For full power .45 loads - AA #5
Grayfox is offline  
Old January 9, 1999, 12:29 PM   #6
bear
Member
 
Join Date: November 13, 1998
Location: Mpls, Minn
Posts: 56
Found the Clays work well in my .45acp.

I was told to try Accurate #7 in my .38 Super but was also told it was a dirty powder????
anybody using it? thanks
bear is offline  
Old January 18, 1999, 11:32 PM   #7
Walt Welch
Senior Member
 
Join Date: November 3, 1998
Location: Alamo, CA
Posts: 424
I have found Hodgdon HS-6 to be very reliable and accurate with moderate to full loads in the 9mm and .45 ACP. In fact, Hodgdon lists +P loads using this powder in the .45 ACP caliber. The spherical powder flows easily through the powder measure, and the powder is fairly clean burning. I have found the use of magnum primers to be unnecessary. It is also available in 8 lb. kegs, which makes it very economical.

I have tried Bullseye, Unique, and W231, but prefer the HS-6. Walt
Walt Welch is offline  
Old January 19, 1999, 08:50 AM   #8
tputto
Member
 
Join Date: January 18, 1999
Location: Joensuu, Finland
Posts: 24
I've been using Vihtavuori N320 in .45 auto and it seems OK, gun doesn't get dirty.
I use Win.primers, 200gr. plated bullets and near max.loads (check www.vihtavuori.fi for data).




tputto is offline  
Old January 19, 1999, 12:43 PM   #9
leapfrog
Senior Member
 
Join Date: January 19, 1999
Location: Texas
Posts: 107
Hi guys, this is my first post to this section - been over on Glock talk mostly. I like Walt Welch's suggestion of HS-6. It is excellent for most all handgun loads, meters well, and is not as dirty as the Accurates and generates fairly low pressures for most applications. By far the cleanest powder I have used is Universal, though the Vihtavouri powders are also very clean by virtue of being single based. If clean is your main objective, use Universal or Vihtavouri.
leapfrog is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:32 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07268 seconds with 9 queries