The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old December 27, 1999, 10:09 AM   #1
zardoz
Member
 
Join Date: December 23, 1999
Location: Burlington, CT, USA
Posts: 39
Will dry firing a gun damage the firing pin?
I've heard yes and no by many people, who's right?
Does the type of gun matter? O/U shotgun? Paraordnance P14? Ruger 10/22? AR-15?
(I don't mean thousands of times but an occasional snap, perhaps to store a gun without tension on hammer spring.)
zardoz is offline  
Old December 27, 1999, 09:15 PM   #2
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Zardoz, dry firing most centerfire firearms won't hurt a thing. But as sure as I say that you'll break your firing pin. Cheap insurance comes in the form of snap caps but the occasional dry fire as you mentioned won't hurt anything. Never dry fire a rimfire. George
George Stringer is offline  
Old December 28, 1999, 09:20 AM   #3
zardoz
Member
 
Join Date: December 23, 1999
Location: Burlington, CT, USA
Posts: 39
Goerge; what will happen to a .22 rimfire if I dry fire the trigger to store in without tension on the hammer springs?
zardoz is offline  
Old December 28, 1999, 04:07 PM   #4
RWK
Senior Member
 
Join Date: August 20, 1999
Location: Occupied Virginia
Posts: 2,777
George,

Please correct me if I am wrong, but I'm fairly sure Sig Sauer specifically recommends no "dry firing" of their "P series" semiautomatics. That, in fact, is one reason they frequently suggest mandatory use of the "decocker".
RWK is offline  
Old December 28, 1999, 06:31 PM   #5
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,681
Hi, folks,

I'll second George and even say that dry firing a properly designed rimfire gun will not hurt anything. The concern there is not that the firing pin might be damaged, but that the firing pin will strike the edge of the chamber and peen it so that a round won't chamber. Still, if designed right, with a solid firing pin stop, this will not happen. With older guns, especially the old "cat rifles", dry firing is harmful.

Most makers of pistols with a decocking device say not to dry fire or let the hammer down for safety reasons, not concern about harming the gun. The decocker blocks the firing pin so it is safer than dropping the hammer (yes, Virginia, people have dropped the hammer on a live round when they thought the gun was empty) or letting it down with the thumb.

If you have that type of gun, get used to using the decocker; it is the best route for safety.

Jim

[This message has been edited by Jim Keenan (edited December 28, 1999).]
James K is offline  
Old January 8, 2000, 10:59 AM   #6
Ruger guy
Senior Member
 
Join Date: January 7, 2000
Posts: 112
Ruger says in their 10/22 instruction manual to dry fire the gun to get used to it and to do it until you are totally comfortable with the basic operation. My son pointed this out to me when I caught him doing it and told him never to dry fire a rim fire.

However, Taurus says to always use snap caps when dry firing their revolvers because the floating firing pin can be damaged.

My baby eagle manual doesn't mention it at all.

I guess it depends on the individual gun.
Ruger guy is offline  
Old January 9, 2000, 06:25 AM   #7
Unkel Gilbey
Senior Member
 
Join Date: February 26, 1999
Location: Danby, Vermont
Posts: 349
I think that as a rule of thumb, it is a good thing to NOT dry fire any rimfire. I say this because there are hundreds of different rimfires out there rifles and pistols, and some you can safely dry fire, and some you shouldn't, etc. Why not load a fired case and snap on that? It works really well in a revolver, and also in bolt actions where you can manually cock the hammer/striker. This way, you can dry fire, and have the means of protecting the chamber with that old shell.
Unkel Gilbey
Unkel Gilbey is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 07:38 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06552 seconds with 9 queries