The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old November 25, 1999, 01:09 AM   #1
loknload
Senior Member
 
Join Date: November 23, 1999
Location: PA. USA
Posts: 1,785
Since this is not an expensive gun and it is not working properly,Not feeding and jamming. I thought I would try and take care of this myself. I have new mags on order to make sure of proper spring tension on the ammo. Now I would like to try my hand at polishing the feed ramp. Any suggestions I have my ideas but thought I would ask if there might be some better ones. Thanks much, in advance
Happy thanksgiving and Happy shooting

------------------
gun control is people control

loknload is offline  
Old November 25, 1999, 09:14 AM   #2
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
loknload, use 400 grit paper or crocus cloth. Wrap around a dowel and polish until smooth. Then progress to finer grits until the finish you want is achieved. I usually finish with a round hard Arkansas stone. Do not change the angle of the ramp. You are polishing not trying to remove any metal. George
George Stringer is offline  
Old November 25, 1999, 11:29 PM   #3
Walt Sherrill
Senior Member
 
Join Date: February 15, 1999
Location: Winston-Salem, NC USA
Posts: 4,539
I also have a CZ-50, as do many on the Curio & Relics List.

They are notorious for magazine problems, and if you're having feeding problems, the odds are very high that the magazine, not the feed ramp, is the problem.

You might want to get a couple of replacement magazines. (Or, if the gun is newly purchased, contact the dealer and ask for a replacement.) (I've seen the mags in Shot Gun News offered by one of the dealers that primarily offers magazines. [Magazine Mania?] About $20.00.)
Walt Sherrill is offline  
Old November 28, 1999, 09:29 AM   #4
BBINJ
Member
 
Join Date: November 19, 1999
Location: Pennsylvania, USA
Posts: 22
These things are NOTORIOUS for failure to feed. Doesn't like those first few rounds out of the mag, does it? On the feed ramp, I true up a brightboy in the Dremel to a radiused end and remove the tool marks (George is right, watch that angle!). Then, use a felt bob with some matchless compound and really get 'er bright & smooth. Stone the breech face super smooth. Radius & polish the leading edge of the extractor (I can't show you how to do this here, but use the same common sense you would on a 1911 or similar extractor. Make sure the extractor moves really smooth in the slide - polish the sides glass smooth. Really slicking up that loaded chamber indicator is a good idea, too. These little stinkers are really rough inside, so detail strip the piece and go hunting for burrs. Use a smooth mill file and remove those horrible broach marks from the outside of the barrel housing on the frame, then polish it bright(this can't hurt, and it looks better bright anyway). Polish your mag followers super smooth, and grind a radius on the front of the mags - this helps those first few "nose-divers" clear the lip of the mag and get on their way up the feed ramp. Also, stay away from that "UMC" garbage that's on sale at K-Mart!
BBINJ is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:28 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.06711 seconds with 9 queries