The Firing Line Forums

Go Back   The Firing Line Forums > The North Corral > Black Powder and Cowboy Action Shooting

Reply
 
Thread Tools
Old February 6, 2005, 11:47 PM   #1
bergwerk
Senior Member
 
Join Date: December 5, 2004
Posts: 142
SA hammer for slip shooting?

My Colt SA might benefit from a hammer designed to ease slip shooting.

First question: where to look for one.

Second question: will slip shooting the hammer while the trigger is held depressed damage anything?
bergwerk is offline  
Old February 7, 2005, 02:01 PM   #2
Jim Watson
Senior Member
 
Join Date: October 25, 2001
Location: Alabama
Posts: 11,000
I think a sliphammer would be pretty much a custom proposition. I doubt it will damage anything until/unless you get so fast that any style would be hard on a SAA.
Jim Watson is offline  
Old February 8, 2005, 02:46 AM   #3
Sir William
Senior Member
 
Join Date: October 13, 2004
Posts: 3,261
Don't do it. It does cause wear and damage. If you really want to do it, get a Ruger and have a gunsmith replace the internals. The action needs to be hardened, geometry angles need to be modified and everything needs to be polished. When you do it, budget for a rebuild also. Slip hammering is not damaging in itself. There are just a few things that can get out of alignment and tolerancs that will change enough to batter the hand and possibly break the bolt if you speed things up. I have broken a few parts and spent some money myself. It is fun and even fastdraw and sliphammering is fun. No, I can't shoot aspirin out of the sky. I have shot in fastdraw, CAS and even exhibition gunfight reenactments. I did break internals, often.
Sir William is offline  
Old February 8, 2005, 05:13 PM   #4
Ozzieman
Senior Member
 
Join Date: December 14, 2004
Location: Northern Indiana
Posts: 4,948
You might want to explane what slip shooting is

Is that where as the gun is pulled out of the holster the thumb brings the hammer back and then slips off with the trigger pulled allowing the gun to fire?
If thats it, I think that a lot of practice with blanks might be in order.
Ozzieman is offline  
Old February 8, 2005, 05:52 PM   #5
Cal4D4
Senior Member
 
Join Date: June 18, 2001
Location: southern california
Posts: 679
Talk to Bob about what you want.


SA rework for slipshooting, etc.
Cal4D4 is offline  
Old February 10, 2005, 09:19 PM   #6
bergwerk
Senior Member
 
Join Date: December 5, 2004
Posts: 142
Yes, with the taped or removed trigger and the cocking thumb slipping sideways from the hammer.

Ed McGivern got me thinking about it but Sir Williams' advice confirms my fears about damage, even though I'm somewhat surprised by his lack of ability with the flying aspirins.

Have you read McGivern's 1938 book?
bergwerk is offline  
Old February 21, 2005, 04:39 PM   #7
beenthere
Senior Member
 
Join Date: November 16, 2004
Location: NE Indiana
Posts: 460
Slip shooting

Ed McGivern was something far out of the ordinary with his handguns and talent. If I remember correctly he even had a pair of handguns with the front of the trigger guard cut out so he didn't lose a couple of thousands of a second inserting his finger in the trigger guard. It might be infintismally faster but it doesn't sound like the safest thing to do. Only my opinion.
beenthere is offline  
Old February 22, 2005, 02:31 AM   #8
bergwerk
Senior Member
 
Join Date: December 5, 2004
Posts: 142
He has photos of those in his book in a chapter titled "Mutilating Guns as an Aid to Speed" and he fired them in DAO mode.

My current obsession is with Colt SAAs, hence the search for slip hammers.
bergwerk is offline  
Old February 22, 2005, 10:15 AM   #9
fal308
Staff Alumnus
 
Join Date: October 12, 1998
Location: Missouri
Posts: 1,986
Slip hammers are used mainly in fast draw competitions. You might check out www.fastdraw.org/wfda/ or www.cowboyfastdrawassociation.com/
fal308 is offline  
Old September 18, 2005, 09:58 AM   #10
WroughtIron
Junior Member
 
Join Date: September 18, 2005
Posts: 2
Belated Slip Hammer Information

Try; "Sixguns". Elmer Keith, has images; "Newman Slip Hammer".
WroughtIron is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 02:31 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07746 seconds with 9 queries