The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old August 20, 1999, 02:39 PM   #1
vanfunk
Senior Member
 
Join Date: June 19, 1999
Posts: 472
Anyone have any tips for effective use of Oxpho-Blue? Is the color at all close to the S&W factory finish? I'll just be using it for touching up some wear spots. Thanks in advance for your wisdom.

------------------
semper ubi sub ubi
vanfunk is offline  
Old August 20, 1999, 03:11 PM   #2
JoeHatley
Senior Member
 
Join Date: July 1, 1999
Location: Iowa
Posts: 2,135
I use the stuff all the time. It will do an okay job for touch ups on your Smith, but it probably isn't going to match the factory blue. If you apply it multiple times, buffing with 0000 steel wool in between each, it will come pretty close. Joe


------------------
Go NRA
JoeHatley is offline  
Old August 23, 1999, 10:11 PM   #3
hclark
Member
 
Join Date: July 18, 1999
Posts: 15
I like the Oxpho Blue, but if you want to get closer to the old S&W blue, use the Dichropan T4 for touch up. I reblued a Luger shooter with Oxpho-Blue and it came out pretty good with some splotches (didn't get rid of all the oil), then came back with the T4 and it really made the "blue" show Up.
hclark is offline  
Old August 25, 1999, 12:29 AM   #4
Dakotan
Senior Member
 
Join Date: August 24, 1999
Posts: 174
Having used Oxpho-Blue (great product!) for about ten years now, I've found that multiple applications are the best way to achieve the darkest coloring. If the area you are touching up can be made horizontal, let the blue "puddle" (or hold a cloth soaked with Oxpho-Blue) on that area for 30 to 60 seconds. It seems that the "wetter" the area stays, the darker the final finish will be. Good Luck and Take Care- Dakotan
Dakotan is offline  
Old August 25, 1999, 01:24 AM   #5
JJR
Senior Member
 
Join Date: June 4, 1999
Location: Idaho
Posts: 381
I tried re-blueing on old 870 last weekend just for fun and I used Oxpho-Blue. After about the 2nd application I could no longer get the blue to "puddle up" as was mentioned. It just beaded up and ran around the metal kinda' like that silver stuff in Terminator II . The darkest finish I could achieve (after a whole afternoon of doing this) was a very light gray. What am I doing wrong?
JJR is offline  
Old August 25, 1999, 07:12 AM   #6
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
The best way to use Oxpho-Blue is to use cotton balls and after the first application, squeeze almost all of the solution out before applying. You only want the ball to be damp. By applying wet you are actually removing the previous application. Then burnish, burnish, burnish with #0000 steel wool. Repeat until desired finish is achieved. George
George Stringer is offline  
Old August 27, 1999, 09:23 AM   #7
jjk308
Junior Member
 
Join Date: August 26, 1999
Location: Oldsmar, FL
Posts: 13
Try heating the metal to just below boiling, apply with 000 steel wool. You don't have to degrease when using the steel wool, some oil seems to spread the blue around more evenly. When done, just wipe with a damp cloth. This is the only cold blue I've found that does not cause after rusting, due to the phosphoric acid in it. It will not blue all steels, however, and case hardened parts may be a problem.
jjk308 is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 09:41 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07637 seconds with 9 queries