The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old July 23, 1999, 06:01 PM   #1
Macoute
Member
 
Join Date: October 9, 1998
Posts: 24
Do the 1911 ambidextrous safeties with the extensions on the right side that fit under the grip panel (Les Baer, Cylinder & Slide, Les Brown, Swenson, etc. - style) require a special right side grip panel allow it to fit? Thanks.
Macoute is offline  
Old July 23, 1999, 07:43 PM   #2
motorep
Senior Member
 
Join Date: October 29, 1998
Location: mid-coast Maine
Posts: 542
Yes, the right panel must be relieved for the ambi safety, but most if not all grips are made with this feature.
motorep is offline  
Old July 24, 1999, 12:43 AM   #3
Grayfox
Senior Member
 
Join Date: December 17, 1998
Posts: 1,885
Check King's Gunworks ambi saftey. It uses a special hammer pin and grooved saftey so that it doesn't relay on the grip panel to hold it in. It would be my choice.
Grayfox is offline  
Old July 25, 1999, 10:44 AM   #4
4V50 Gary
Staff
 
Join Date: November 2, 1998
Location: Colorado
Posts: 17,048
I don't think the Colt ambidextrious safety requires the right grip panel to be relieved. What Colt (actually subcontracted out to Menscke) did was to mill a lip along the edge of the left thumb safety. A longer sear pin with a dovetail cut is used to engage that milled lip, thereby preventing the left thumb safety from walking out of the gun. For me, it's easily the best there is. Not fancy, but darn clever.

------------------
Vigilantibus et non dormientibus jura subveniunt

4V50 Gary is online now  
Old July 25, 1999, 07:55 PM   #5
Jim V
Senior Member
 
Join Date: January 31, 1999
Location: SE Michigan - USA
Posts: 4,038
"Lone Wolf" Gonzalaus, Texas Ranger, had such a set of ambisafetys fitted to his 1911's long before they were commonly on the market.

I hope I spelled EL Lobo Solo's last name correctly.

------------------
Ne Conjuge Nobiscum
"If there be treachery, let there be jehad!"

Jim V is offline  
Old July 26, 1999, 01:23 AM   #6
burrhead
Senior Member
 
Join Date: July 6, 1999
Location: Chihuahuan desert, Texas
Posts: 434
I've been a 1911 fan for 25+ years, and a lefty even before that, so I've used many brands of ambi safeties. Tried the Colt system several years ago and the right thumb piece kept flying off. Thought it was junk. Went to Swenson's because he was state of the art at the time. I've used a few others since then and they've all done the job. I now use Brown's just because the ergonomics work best for me. Any of the major brands made now should work ok; boils down to what feels best to you. Releaving the right grip panel is not a big problem. If a qunsmith installs the safety for you the grip alterations should be part of the deal.
burrhead is online now  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:45 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07902 seconds with 9 queries