The Firing Line Forums

Go Back   The Firing Line Forums > The Skunkworks > The Smithy

Reply
 
Thread Tools
Old June 29, 1999, 04:44 AM   #1
Macoute
Member
 
Join Date: October 9, 1998
Posts: 24
I just got a S&w revolver and the owner's manual was somewhat vague on lubrication. Where do you place oil on a revolver to lubricate it? Also what have you found to be the best solvent/method to remove leading from the bore and forcing cone? Thanks.
Macoute is offline  
Old June 29, 1999, 07:48 AM   #2
George Stringer
Staff Alumnus
 
Join Date: October 12, 1998
Location: Earlington KY
Posts: 2,299
Macoute, occasionally you can remove the side plate and put a drop of oil on the parts if it's needed but unless you're comfortable with disassembly/assembly of the pistol I wouldn't recommend it. The easiest thing to do is to keep the outside, the bore and chambers clean and lightly oiled. Then about every six months to a year, depending on how much you shoot, take it too your local smith for a detailed clean and oil. He'll completely disassemble the pistol and clean it. The best thing I've found for leaded bores and forcing cones is the Lewis Lead Remover. You might find one at Wal-Mart. If not, surely your local gun shop will have or be able to get one for you. George
George Stringer is offline  
Old June 29, 1999, 11:11 AM   #3
BigG
Senior Member
 
Join Date: May 19, 1999
Location: Atlanta, GA
Posts: 4,318
Other than cleaning the bore and cylinder, I put a drop of lube on the two spring loaded detents that hold the cylinder in on the S&W. and wipe the gun down with a silicone cloth. My S&Ws look like new after years of use.

------------------
Yankee Doodle


BigG is offline  
Old June 29, 1999, 01:58 PM   #4
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,951
All you need do with a S&W revolver in the way of lubrication is:

1. Make sure gun is not loaded.
2. With cylinder closed, cock hammer.
3. Drop 4-5 drops of oil into the space ahead of the hammer.
4. Drop 3-4 drops of oil into the space ahead of the trigger (bottom of frame)
5. Uncock hammer and open cylinder, push back extractor, drop 2 drops of oil on extractor shaft, working back and forth.
6. Drop 2-3 drops of oil on ratchet.
7. Drop 1 drop of oil in end of ejector rod.

That's it - a couple of minutes.

As for leading, that is another problem. FWIW, I think the best lead remover for revolver barrels and cylinders is the old Lewis lead remover. There are all kinds of chemicals and even an (expensive) electronic gadget. Most of these are fine, although some of the chemical cleaners are pretty useless and ones with ammonia can really wreck nickel plate if it can get at the copper undercladding.

Again FWIW, I use G96 Gun Treatment, which cleans and leaves a protective film.

Jim

James K is offline  
Old June 29, 1999, 07:37 PM   #5
swifter...
Senior Member
 
Join Date: March 16, 1999
Location: So. CA Mountains
Posts: 540
A thought on lead removal: Get a Chore Girl, or other brass pot scrubber. Cut into it with tinsnips/wire cutter so you can pull the individual strands out. Wrap some of these strands around a bore brush, preferably a worn one... And scrub hell outa the bore with your choice of solvent. Cheaper than the LLR, at least as effective, and adaptable to all calibers.
Don't overoil, and don't use teflon oils in the bore.

------------------
Shoot carefully... swifter...


swifter... is offline  
Old July 1, 1999, 12:53 PM   #6
James K
Staff
 
Join Date: March 17, 1999
Posts: 19,951
Good thinking, Swifter.

I might also note that the brass and copper pot scrubbers are great for removing surface rust and provide a good surface for cold blue to boot.

Jim
James K is offline  
Reply

Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -5. The time now is 08:05 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
This site and contents, including all posts, Copyright © 1998-2014 S.W.A.T. Magazine
Copyright Complaints: Please direct DMCA Takedown Notices to the registered agent: thefiringline.com
Contact Us
Page generated in 0.07734 seconds with 9 queries